Toyota CH-R Service Manual: Blind Spot Monitor System
Toyota CH-R Service Manual / Park Assist / Monitoring / Blind Spot Monitor System
- Precaution
- Parts Location
- System Diagram
- How To Proceed With Troubleshooting
- System Description
- Operation Check
- Customize Parameters
- Problem Symptoms Table
- Diagnosis System
- Terminals Of Ecu
- Dtc Check / Clear
- Freeze Frame Data
- Data List / Active Test
- Master Module Horizontal Axis Misalignment (C1AC1)
- Diagnostic Trouble Code Chart
- Slave Module Horizontal Axis Misalignment (C1AC2)
- Lost Communication with ECM / PCM "A" (U0100,U0125,U0126,U0129,U0142)
- Lost Communication with Blind Spot Monitor Slave Module (U0232)
- Software Incompatibility with Body Control Module "B" (U1331)
- Short to GND or Open in Buzzer (C1ABE)
- Blind Spot Monitor Slave Module Beam Axis Inspection Incomplete (C1ABC)
- Destination Information Undefined (C1AB8)
- Blind Spot Monitor Master Module Beam Axis Inspection Incomplete (C1ABB)
- Blind Spot Monitor Master Module (C1AB6)
- Blind Spot Monitor Slave Module (C1AB7)
- Open in Outer Mirror Indicator(Slave) (C1AB5)
- Open in Outer Mirror Indicator(Master) (C1AB4)
- Short to GND in Outer Mirror Indicator(Slave) (C1AB3)
- Short to +B in Outer Mirror Indicator(Slave) (C1AB1)
- Short to GND in Outer Mirror Indicator(Master) (C1AB2)
- Short to +B in Outer Mirror Indicator(Master) (C1AB0)
- Steering Angle Sensor (C1A47)
- Vehicle Speed Sensor (C1A45)
- Yaw Rate Sensor (C1A46)
- Power Source Circuit
Blind Spot Monitor Sensor
Components
COMPONENTS
ILLUSTRATION
*1
BLIND SPOT MONITOR BRACKET LH
*2
BLIND SPOT MONITOR BRACKET RH
*3
BLIND SPOT MONITO ...
Precaution
PRECAUTION
IGNITION SWITCH EXPRESSIONS
(a) The type of ignition switch used on this model differs depending on the specifications
of the vehicle. The expressions listed in the table below are used ...
Other materials:
Toyota CH-R Service Manual > Brake Booster: Disassembly
DISASSEMBLY
PROCEDURE
1. REMOVE BRAKE VACUUM CHECK VALVE ASSEMBLY
(a) Remove the brake vacuum check valve assembly from the brake booster assembly.
(b) Remove the check valve grommet from the brake booster assembly.
2. REMOVE VACUUM WARNING SWITCH ASSEMBLY
(a) Remove the vacuum warning switc ...
Toyota CH-R Service Manual > Airbag System: Check Mode Procedure
CHECK MODE PROCEDURE
CHECK MODE (SIGNAL CHECK): DTC CHECK
(a) Turn the ignition switch off.
(b) Connect the Techstream to the DLC3.
(c) Turn the ignition switch ON.
(d) Turn the Techstream on.
(e) Enter the following menus: Body Electrical / SRS Airbag / Utility / Signal
Check.
Body Electri ...
Toyota CH-R Owners Manual
- For safety and security
- Instrument cluster
- Operation of each component
- Driving
- Interior features
- Maintenance and care
- When trouble arises
- Vehicle specifications
- For owners
Toyota CH-R Service Manual
- Introduction
- Maintenance
- Audio / Video
- Cellular Communication
- Navigation / Multi Info Display
- Park Assist / Monitoring
- Brake (front)
- Brake (rear)
- Brake Control / Dynamic Control Systems
- Brake System (other)
- Parking Brake
- Axle And Differential
- Drive Shaft / Propeller Shaft
- K114 Cvt
- 3zr-fae Battery / Charging
- Networking
- Power Distribution
- Power Assist Systems
- Steering Column
- Steering Gear / Linkage
- Alignment / Handling Diagnosis
- Front Suspension
- Rear Suspension
- Tire / Wheel
- Tire Pressure Monitoring
- Door / Hatch
- Exterior Panels / Trim
- Horn
- Lighting (ext)
- Mirror (ext)
- Window / Glass
- Wiper / Washer
- Door Lock
- Heating / Air Conditioning
- Interior Panels / Trim
- Lighting (int)
- Meter / Gauge / Display
- Mirror (int)
- Power Outlets (int)
- Pre-collision
- Seat
- Seat Belt
- Supplemental Restraint Systems
- Theft Deterrent / Keyless Entry
© 2017-2025 Copyright www.tochr.net
0.015
0.015