Toyota CH-R Service Manual: Customize Parameters
CUSTOMIZE PARAMETERS
CUSTOMIZE BLIND SPOT MONITOR SYSTEM
(a) Customizing with the Techstream
NOTICE:
- When the customer requests a change in a function, first make sure that the function can be customized.
- Be sure to make a note of the current settings before customizing.
- When troubleshooting a function, first make sure that the function is set to the default setting.
(1) Connect the Techstream to the DLC3.
(2) Turn the ignition switch to ON.
(3) Turn the blind spot monitor system on.
(4) Turn the Techstream on.
(5) Enter the following menus: Body Electrical / Blind Spot Monitor Master or Blind Spot Monitor Slave / Utility / Warning.
(6) Select the setting by referring to the table below.
Warning|
Tester Display |
Description |
Default |
Setting |
ECU |
|---|---|---|---|---|
|
BSM Buzzer Volume Adjust |
Sets the volume of the RCTA buzzer (blind spot monitor buzzer). |
Medium |
001:Low,011:Medium,101:High |
Blind Spot Monitor Sensor LH (Master) |
|
BSM Mirror Indicator Brightness |
Sets the brightness of the indicators in the outer rear view mirror assemblies. |
Bright |
001:Dark,101:Bright |
Blind Spot Monitor Sensor LH (Master) |
|
RCTA Function |
Switches the RCTA function on and off. |
ON |
0:ON,1:OFF |
Blind Spot Monitor Sensor RH (Slave) |
Operation Check
OPERATION CHECK
HINT:
The blind spot monitor beam axis confirmation is performed to confirm whether
the sensor's beam axis is correct, and perform adjustment of the beam axis by using
reflec ...
Problem Symptoms Table
PROBLEM SYMPTOMS TABLE
HINT:
Use the table below to help determine the cause of problem symptoms.
If multiple suspected areas are listed, the potential causes of the symptoms
are lis ...
Other materials:
Toyota CH-R Service Manual > Wireless Door Lock Control System(w/ Smart Key System): System Diagram
SYSTEM DIAGRAM
Wireless Door Lock Control System
Communication Table
Sender
Receiver
Signal
Line
Certification ECU
(Smart Key ECU Assembly)
Main Body ECU
(Multiplex Network Body ECU)
Wireless door lock ...
Toyota CH-R Service Manual > Rear Spoiler: Installation
INSTALLATION
PROCEDURE
1. INSTALL REAR SPOILER ASSEMBLY
(a) Engage the clips to install the rear spoiler assembly as shown in the illustration.
Install in this Direction
(b) Install the 8 nuts.
Torque:
6.0 N·m {61 kgf·cm, 53 in·lbf}
(c) Connect the connecto ...
Toyota CH-R Owners Manual
- For safety and security
- Instrument cluster
- Operation of each component
- Driving
- Interior features
- Maintenance and care
- When trouble arises
- Vehicle specifications
- For owners
Toyota CH-R Service Manual
- Introduction
- Maintenance
- Audio / Video
- Cellular Communication
- Navigation / Multi Info Display
- Park Assist / Monitoring
- Brake (front)
- Brake (rear)
- Brake Control / Dynamic Control Systems
- Brake System (other)
- Parking Brake
- Axle And Differential
- Drive Shaft / Propeller Shaft
- K114 Cvt
- 3zr-fae Battery / Charging
- Networking
- Power Distribution
- Power Assist Systems
- Steering Column
- Steering Gear / Linkage
- Alignment / Handling Diagnosis
- Front Suspension
- Rear Suspension
- Tire / Wheel
- Tire Pressure Monitoring
- Door / Hatch
- Exterior Panels / Trim
- Horn
- Lighting (ext)
- Mirror (ext)
- Window / Glass
- Wiper / Washer
- Door Lock
- Heating / Air Conditioning
- Interior Panels / Trim
- Lighting (int)
- Meter / Gauge / Display
- Mirror (int)
- Power Outlets (int)
- Pre-collision
- Seat
- Seat Belt
- Supplemental Restraint Systems
- Theft Deterrent / Keyless Entry
0.0104