Toyota CH-R Service Manual: Installation

INSTALLATION

CAUTION / NOTICE / HINT

PROCEDURE

1. INSTALL REAR DISC

(a) Align the matchmarks of the rear disc and rear axle hub and bearing assembly, and install the rear disc. NOTICE: When replacing the rear disc with a new one, select the installation position where the rear disc has minimal runout.

*a Matchmark

2. INSTALL REAR DISC BRAKE CYLINDER MOUNTING

(a) Install the rear disc brake cylinder mounting to the rear axle carrier sub-assembly with the 2 bolts.

Torque:

107 N·m {1091 kgf·cm, 79 ft·lbf}

3. INSTALL REAR DISC BRAKE BUSHING DUST BOOT

(a) Apply a light layer of lithium soap base glycol grease to the entire circumference of 2 new rear disc brake bushing dust boots.

HINT:

Apply more than 0.3 g (0.01 oz.) of lithium soap base glycol grease to each rear disc brake bushing dust boot.

Lithium Soap Base Glycol Grease

(b) Install the 2 rear disc brake bushing dust boots to the rear disc brake cylinder mounting.

4. INSTALL REAR DISC BRAKE CYLINDER SLIDE PIN

Lithium Soap Base Glycol Grease

(a) Apply a light layer of lithium soap base glycol grease to the contact surface of the rear No. 2 disc brake cylinder slide pin.

(b) Install a new rear disc brake cylinder slide bushing to the rear No. 2 disc brake cylinder slide pin.

Lithium Soap Base Glycol Grease

(c) Apply a light layer of lithium soap base glycol grease to the sliding part and the sealing surfaces of the rear No. 1 disc brake cylinder slide pin and rear No. 2 disc brake cylinder slide pin.

(d) Install the rear No. 1 disc brake cylinder slide pin and rear No. 2 disc brake cylinder slide pin to the rear disc brake cylinder mounting.

*1 Rear No. 1 Disc Brake Cylinder Slide Pin *2 Rear No. 2 Disc Brake Cylinder Slide Pin

(e) Push the rear No. 1 disc brake cylinder slide pin and rear No. 2 disc brake cylinder slide pin into each rear disc brake bushing dust boot to engage the pins to the boots.

5. INSTALL REAR DISC BRAKE PAD SUPPORT PLATE

(a) Install the 4 rear disc brake pad support plates to the rear disc brake cylinder mounting.

NOTICE:

Be sure to install each rear disc brake pad support plate in the correct position and direction.

6. INSTALL REAR DISC BRAKE ANTI-SQUEAL SHIM

Click here

7. INSTALL REAR DISC BRAKE PAD

(a) Install the 2 rear disc brake pads to the rear disc brake cylinder mounting.

NOTICE:

Install the rear disc brake pad so that the rear disc brake pad wear indicator plate is mounted on the lower side of the vehicle.

HINT:

If the rear disc brake pad has an identification mark, be sure to confirm the installation location.

8. INSTALL REAR DISC BRAKE CYLINDER ASSEMBLY

(a) Hold the 2 rear disc brake cylinder slide pins, and install the rear disc brake cylinder assembly to the rear disc brake cylinder mounting with the 2 new bolts in the order shown in the illustration. Torque: 34.3 N·m {350 kgf·cm, 25 ft·lbf}

*a Hold *b Turn

9. INSTALL PARKING BRAKE ACTUATOR ASSEMBLY

(a) Apply a light coat of lithium soap base glycol grease to a new O-ring.

(b) Install the O-ring to the rear disc brake cylinder assembly.

NOTICE:

Make sure to replace the O-ring with a new one when installing the parking brake actuator assembly.

(c) Using a 5 mm hexagon socket wrench, install the parking brake actuator assembly to the rear disc brake cylinder assembly with the 2 bolts.

Torque:

8.4 N·m {86 kgf·cm, 74 in·lbf}

10. CONNECT NO. 2 PARKING BRAKE WIRE ASSEMBLY

(a) Connect the No. 2 parking brake wire assembly connector to the parking brake actuator assembly.

11. CONNECT REAR FLEXIBLE HOSE

(a) Connect the rear flexible hose to the rear disc brake cylinder assembly with a new union bolt and a new gasket.

Torque:

30.4 N·m {310 kgf·cm, 22 ft·lbf}

NOTICE:

Install the rear flexible hose lock securely into the lock hole in the rear disc brake cylinder assembly.

12. BLEED BRAKE LINE

Click here

13. BLEED REAR DISC BRAKE CYLINDER ASSEMBLY

CAUTION:

If the rear disc brake cylinder assembly has been disassembled, perform air bleeding for the rear disc brake cylinder.

(a) Perform the procedure to enter rear disc brake pad replacement mode 5 times.

Click here

(b) Release the parking brake.

(c) Disconnect the No. 2 parking brake wire assembly connector from the parking brake actuator assembly.

(d) Remove the center No. 1 cowl top ventilator louver.

Click here

(e) Remove the brake master cylinder reservoir filler cap.

(f) Add brake fluid to keep the level between the MIN and MAX lines of the reservoir while bleeding the brakes.

(g) Remove the bolt and separate the rear disc brake cylinder assembly.(*1) NOTICE: Keep the rear no. 2 disc brake cylinder slide pin free of foreign matter.

*a Turn *b Hold

(h) Hold the rear disc brake cylinder assembly horizontally, then tilt it 45° toward the bleeder plug side as shown in the illustration.(*2)

(i) Temporarily install the rear disc brake cylinder assembly with the bolt.(*3)

*a Turn *b Hold

(j) Depress the brake pedal several times, and then loosen the bleeder plug with the pedal depressed.(*4)

(k) When fluid stops coming out, tighten the bleeder plug and release the brake pedal.(*5)

(l) Repeat steps (*1) through (*5) 3 times.

NOTICE:

If there is still air in the system after performing steps (*1) through (*5) 3 times, repeat the steps (*1) through (*5) until the air has been bled.

(m) Tighten the bleeder plug completely.

Torque:

8.3 N·m {85 kgf·cm, 73 in·lbf}

(n) Install the rear disc brake cylinder assembly with a new bolt.

Torque:

34.3 N·m {350 kgf·cm, 25 ft·lbf}

(o) Connect the No. 2 parking brake wire assembly connector to the parking brake actuator assembly.

(p) Inspect for brake fluid leaks.

(q) Inspect the brake fluid level in the reservoir.

Click here

(r) Install the brake master cylinder reservoir filler cap assembly.

(s) Install the center No. 1 cowl top ventilator louver.

Click here

14. INSTALL REAR WHEEL

Click here

15. NORMAL CONDITION RECOVERY

Click here