Toyota CH-R Service Manual: Data List / Active Test

DATA LIST / ACTIVE TEST

DATA LIST

NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

HINT:

Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

(a) Warm up the engine.

(b) Turn the ignition switch off.

(c) Connect the Techstream to the DLC3.

(d) Turn the ignition switch ON.

(e) Turn the Techstream on.

(f) Enter the following menus:

(1) for Combination Meter: Body Electrical / Combination Meter / Data List.

(2) for ABS/VSC/TRAC/EPB: Chassis / ABS/VSC/TRAC/EPB / Data List.

(3) for Engine: Powertrain / Engine / Data List.

(g) Read the Data List according to the display on the Techstream.

(1) Combination Meter

Body Electrical > Combination Meter > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

P-Seatbelt Buckle SW

Front passenger seat belt buckle switch

OFF or ON

OFF: Front passenger seat belt fastened

ON: Front passenger seat belt unfastened

-

Vehicle Speed Meter

Vehicle speed

Min.: 0 km/h (0 mph), Max.: 255 km/h (158 mph)

Almost the same as actual vehicle speed

-

Engine Rpm

Engine speed

Min.: 0 rpm, Max.:12750 rpm

Almost the same as actual tachometer

-

Coolant Temperature

Engine coolant temperature

Min.: 0°C (0°F), Max.: 127.5°C(261.5°F)

75 to 100°C (167 to 212°F): After warming up engine

-

Water Level SW

Level warning switch

OFF or ON

OFF: Level warning switch off

ON: Level warning switch on

-

Multi Display Select Switch

Steering pad switch (DISP)

OFF or ON

OFF: Steering pad switch (DISP) released

ON: Steering pad switch (DISP) pushed

-

+B Voltage Value

Battery voltage

Min.: 0 V, Max.:25.5 V

11 to 14 V

-

Fuel Input

Fuel input

Min.: 0 L, Max.:127.5 L

  • Fuel receiver gauge indicates

    F: 45.0 L

  • Fuel receiver gauge indicates

    3/4: 35.4 L

  • Fuel receiver gauge indicates

    1/2: 25.0 L

  • Fuel receiver gauge indicates

    1/4: 14.6 L

  • Fuel receiver gauge indicates

    E: 5.0 L

Unit: Liter

Ambient Temperature

Outside temperature

Min.: -40°C (-40°F), Max.: 87.5°C (189.5°F)

Almost the same as actual outside temperature

The temperature displayed on the multi-information display is -40 to 50°C (-40 to 122°F)

Rheostat value

Light control rheostat switch input

Min.: 0%, Max.: 100%

Increases from 0 to 100 as light control rheostat switch turned from left to right

-

HV System Indicator

Hybrid system indicator value

Min.: -101%, Max.: 511%

-101 to 511%

*1

Multi Switch (Up)

Steering pad switch(Up)

OFF or ON

OFF: Switch released

ON: Switch pushed

-

Multi Switch (Down)

Steering pad switch(Down)

OFF or ON

OFF: Switch released

ON: Switch pushed

-

Multi Switch (Menu)

Steering pad switch(Menu)

OFF or ON

OFF: Switch released

ON: Switch pushed

-

Multi Switch (Enter)

Steering pad switch(Enter)

OFF or ON

OFF: Switch released

ON: Switch pushed

-

Multi Switch (Right)

Steering pad switch(Right)

OFF or ON

OFF: Switch released

ON: Switch pushed

-

Multi Switch (Left)

Steering pad switch(Left)

OFF or ON

OFF: Switch released

ON: Switch pushed

-

2nd-Row Seatbelt Buckle (R)

Buckle switch (rear RH side)

OFF or ON

OFF: Tongue plate (for Rear RH side) not inserted

ON: Tongue plate (for Rear RH side) inserted

*2

2nd-Row Seatbelt Buckle (L)

Buckle switch (rear RH side)

OFF or ON

OFF: Tongue plate (for Rear LH side) not inserted

ON: Tongue plate (for Rear LH side) inserted

*2

2nd-Row Seatbelt Buckle (C)

Buckle switch (rear RH side)

OFF or ON

OFF: Tongue plate (for Rear center) not inserted

ON: Tongue plate (for Rear center) inserted

*2

Oil Pressure Switch

Oil pressure switch

OFF or ON

OFF: Engine started

ON: Engine not started

-

Turn Signal Switch (Right)

Oil pressure switch

OFF or ON

OFF: RH turn signal switch off

ON: RH turn signal switch on

-

Turn Signal Switch (Left)

LH turn signal switch

OFF or ON

OFF: LH turn signal switch off

ON: LH turn signal switch on

-

Hazard Flasher Switch

Hazard warning signal switch

OFF or ON

OFF: Hazard warning signal switch off

ON: Hazard warning signal switch on

-

Passenger Occupant Detection Switch

Occupant detection sensor

OFF or ON

OFF: Front passenger seat not occupied

ON: Front passenger seat occupied

*3

Turn Switch Signal (Full Turn)

Turn signal switch status

OFF or ON

OFF: Turn signal switch off

ON: Turn signal switch on (Full Turn)

-

Multi Switch (Back)

Steering pad switch(Back)

OFF or ON

OFF: Switch released

ON: Switch pushed

-

Key Remind Sound

Condition of the key reminder sound adjustment

Normal, Slow, Fast

Customized value displayed

*4

Driver Side Seatbelt Warning Buzzer

Setting of the driver seatbelt warning buzzer

OFF or ON

OFF: Seatbelt warning buzzer does not sound at vehicle speed of 20 km/h (12 mph) or more when driver seat belt unfastened

ON: Seatbelt warning buzzer sounds at vehicle speed of 20 km/h (12 mph) or more when driver seat belt unfastened

Displays customize setting of Driver Side Seatbelt Warning Buzzer

P-Seatbelt Warning Buzzer

Setting of the front passenger seatbelt warning buzzer

OFF or ON

OFF: Seatbelt warning buzzer does not sound at vehicle speed of 20 km/h (12 mph) or more when front passenger seatbelt unfastened

ON: Seatbelt warning buzzer sounds at vehicle speed of 20 km/h (12 mph) or more when front passenger seatbelt unfastened

Displays customize setting of Front Passenger Side Seatbelt Warning Buzzer

Rear Seatbelt Warning Buzzer

Rear seat belt warning buzzer

OFF or ON

Customized value displayed

*2

ECO Drive Indicator Zone

Setting of the ECO drive indicator zone

OFF or ON

OFF: Active

ON: Non Active

-

ECO Drive Indicator Light

Condition of the eco drive indicator light

OFF or ON

Customized value displayed

-

ODO Display Time After IG OFF Setting

Setting of the ODO display time after the ignition switch is turned off

30s, 60s, 600s, OFF

Displays customize setting of ODO display time after the ignition switch is turned off

-

Lane Change Flashing Times Setting

Setting of the lane change flashing times

OFF, 3, 4, 5, 6, 7

Customized value displayed

-

TPMS System

Existence of function

With or Without

With: w/ Tire pressure warning system

Without: w/o Tire pressure warning system

-

LDA System

Existence of function

With or Without

With: w/ Toyota safety sense P

Without: w/o Toyota safety sense P

-

VSC System

Existence of function

With or Without

With: w/ Vehicle stability control system

Without: w/o Vehicle stability control system

-

PCS System

Existence of function

With or Without

With: w/ Toyota safety sense P

Without: w/o Toyota safety sense P

-

ICS System

Existence of function

With or Without

With: w/ Intelligent clearance sonar system

Without: w/o Intelligent clearance sonar system

-

Radar Cruise System

Existence of function

With or Without

With: w/ Toyota safety sense P

Without: w/o Toyota safety sense P

-

Flasher Sound Tone Setting

Condition of the flasher sound tone adjustment

Tone 1,Tone 2,Tone 3

Customized value displayed

-

Clearance Sonar System

Existence of function

With or Without

With: w/ Intuitive parking assist System

Without: w/o Intuitive parking assist System

-

Road Sign Assist System

Existence of function

With or Without

With: w/ Road sign assist system

Without: w/o Road sign assist system

-

Number of Trouble Code

The number of the DTC currently stored

Min.: 0, Max.: 255

0

-

  • *1: Although the item is displayed on the Techstream, it is not applicable to this vehicle.
  • *2: w/ Rear Passenger Seat Belt Warning
  • *3: w/o Occupant Classification System
  • *4: w/o Smart Key System

(2) ABS/VSC/TRAC/EPB

Chassis > ABS/VSC/TRAC/EPB > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

Vehicle Speed

Maximum wheel speed sensor reading

Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)

Vehicle stopped: 0 km/h (0 mph)

When driving at constant speed: No large fluctuations

(3) Engine and ECT

Powertrain > Engine and ECT > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

Engine Speed

Engine speed

Min.: 0 rpm, Max.: 16383 rpm

710 to 810 rpm: Idling with warm engine

When the crankshaft position sensor is malfunctioning, "Engine Speed" is approximately 0 rpm or varies greatly from the actual engine speed.

Coolant Temp

Engine coolant temperature

Min.: -40°C (-40°F), Max.: 140°C (284°F)

75 to 100°C (167 to 212°F): After warming up engine

This is the engine coolant temperature.

HINT:

  • After warming up the engine, the engine coolant temperature is 75 to 100°C (167 to 212°F).
  • After a long soak, the engine coolant temperature, intake air temperature and ambient temperature are approximately equal.
  • If the value is -40°C (-40°F), or 135°C (275°F), the sensor circuit is open or shorted.
  • Check if the engine overheats when the value indicates 135°C (275°F).

ACTIVE TEST

HINT:

Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

(a) Connect the Techstream to the DLC3.

(b) Turn the ignition switch ON.

(c) Turn the Techstream on.

(d) Enter the following menus: Body Electrical / Combination Meter / Active Test.

(e) Perform the Active Test according the display on the Techstream.

Body Electrical > Combination Meter > Active Test

Tester Display

Measurement Item

Control Range

Diagnostic Note

Speed Meter Operation

Speedometer

OFF, 0, 40, 80, 120, 160, 200, 240, 280

There is a deviation in the values displayed on the speedometer (Control range → Speedometer display)

(1)for Gauge speedometer*1 Reference km/h:
  • 40 → 41.7 to 46.2
  • 80 → 83.4 to 88.4
  • 120 → 125.1 to 130.6
  • 160 → 166.2 to 173.2
  • 200 → 207.7 to 215.7
(2)for Gauge speedometer*2 Reference km/h:
  • 40 → 38.7 to 43.2
  • 80 → 79.3 to 84.3
  • 120 → 120.3 to 125.3
  • 200 → 202.1 to 207.1
(3)for Gauge speedometer*3 Reference mph:
  • 40 → 39.5 to 42.3
  • 80 → 80.2 to 83.4
  • 120 → 121.2 to 124.4

TachoMeter Operation

Tachometer

OFF, 0, 1000, 2000, 3000, 4000, 5000, 6000, 7000

-

Fuel Meter Operation

Fuel receiver gauge

OFF, Sender E, Empty, Warning, 1/4, 1/2, 3/4, Full, Sender F

See Fuel Meter Operation

A/T Indicator Operation 1

Shift indicator

OFF, L, 2, 3(M), 4(M), D, N, R, P

-

A/T Indicator Operation 2

Shift indicator

Shift indicator OFF, 8, 5, 6, 7, M

-

A/T Indicator Operation 3

Shift indicator

Shift indicator OFF, D, SIL (Up), SIL (Down)

-

Indicat. Lamp Airbag

SRS warning light

OFF or ON

-

Driver Side Seat Belt

Driver or front passenger seat belt warning light

OFF or ON

-

Indicat. Lamp ABS

ABS warning light

OFF or ON

-

Indicat. Lamp Slip

Slip indicator light

OFF or ON

-

Indicat. Lamp Beam

High beam indicator light

OFF or ON

-

Indicat. Lamp Head

Head indicator light

OFF or ON

*4

Indicat. Lamp Tail

Tail indicator light

OFF or ON

*5

Indicat. Lamp Fr FOG

Front fog indicator light

OFF or ON

*6

Indicat. Pre-Collision

PCS warning light

OFF or ON

*7

Indicat. Lamp Fuel

Fuel level warning light

OFF or ON

-

Indicat. Tire Pressure Warning System

Tire pressure warning light

OFF or ON

-

Indicat. Lamp ECB

Brake warning light / yellow (minor malfunction)

OFF or ON

-

Indicat. Lamp Brake

Brake warning light

OFF or ON

-

Indicat. EPS

EPS warning light

OFF or ON

-

Master Warning

Master warning light

OFF or ON

*9

Indicat. Park

Parking brake warning light

OFF or ON

-

Indicat. VSC OFF

VSC OFF indicator light

OFF or ON

-

Automatic High Beam Indicator

Automatic high beam indicator light

OFF or ON

*7

PPS Indicator

EPS warning light

OFF or ON

-

Turn Signal (Left) Indicator

LH turn indicator light

OFF or ON

-

Turn Signal (Right) Indicator

RH turn indicator light

OFF or ON

-

Check Engine Indicator

MIL (Check engine warning light)

OFF or ON

-

BSM Control Indicator

BSM indicator light

OFF or ON

*8

Water Temperature Meter Operation

Engine coolant temperature receiver gauge

OFF, LOW, NORMAL, HIGH

See Water Temperature Meter Operation

Meter Display 1

Multi-information display

OFF, All

-

  • *1: w/o Occupant Classification System
  • *2: w/ Occupant Classification System and w/o Daytime Running Light OFF function
  • *3: w/ Occupant Classification System and w/ Daytime Running Light OFF function
  • *4: w/ HEAD Indicator
  • *5: w/ TAIL Indicator
  • *6: w/ Front Fog Light
  • *7: w/ Toyota Safety Sense P
  • *8: w/ Blind Spot Monitor System
  • *9: Although the item is displayed on the Techstream, it is not applicable to this vehicle.

(1) Fuel meter operation. (w/ Occupant Classification System)

*A

Sender E

*B

Empty

*C

Warning

*D

1/4

*E

1/2

*F

3/4

*G

Full

*H

Sender F

(2) Fuel meter operation. (w/o Occupant Classification System)

*A

Sender E

*B

Empty

*C

Warning

*D

1/4

*E

1/2

*F

3/4

*G

Full

*H

Sender F

(3) Water temperature meter operation.

*A

LOW

*B

NORMAL

*C

HIGH

    Terminals Of Ecu
    TERMINALS OF ECU COMBINATION METER ASSEMBLY (a) Disconnect the combination meter assembly connectors. (b) Measure the voltage on the wire harness side connector according to the value(s) in the ...

    Dtc Check / Clear
    DTC CHECK / CLEAR CHECK DTC (a) Connect the Techstream to the DLC3. (b) Turn the ignition switch ON. (c) Turn the Techstream on. (d) Enter the following menus: Body Electrical / Combination Meter ...

    Other materials:

    Toyota CH-R Service Manual > Airbag System: TC and CG Terminal Circuit
    DESCRIPTION DTC output mode is set by connecting terminals TC and CG of the DLC3. DTCs are displayed by blinking of the SRS warning light. HINT: When multiple warning lights in the combination meter blink continuously, a short to ground in the wiring or an ECU connected to terminal T ...

    Toyota CH-R Service Manual > Automatic Headlight Beam Level Control System: Vehicle Specifications have not been Stored (B2451)
    DESCRIPTION The headlight ECU sub-assembly LH stores this DTC if the vehicle specifications have not been stored in the ECU. DTC No. Detection Item DTC Detection Condition Trouble Area Note B2451 Vehicle Specifica ...

    Toyota CH-R Owners Manual

    Toyota CH-R Service Manual

    © 2017-2024 Copyright www.tochr.net
    0.0122