Toyota CH-R Service Manual: Reassembly

Toyota CH-R Service Manual / Brake (rear) / Rear Brake(for Tmc Made) / Reassembly

REASSEMBLY

PROCEDURE

1. TEMPORARILY TIGHTEN REAR DISC BRAKE BLEEDER PLUG

(a) Temporarily install the rear disc brake bleeder plug to the rear disc brake cylinder assembly.

HINT:

Fully tighten the rear disc brake bleeder plug after bleeding the system.

2. INSTALL REAR DISC BRAKE BLEEDER PLUG CAP

(a) Install the rear disc brake bleeder plug cap to the rear disc brake bleeder plug.

3. INSTALL PISTON SEAL

(a) Apply lithium soap base glycol grease to the entire circumference of a new piston seal.

Lithium Soap Base Glycol Grease

(b) Install the piston seal to the rear disc brake cylinder assembly.

NOTICE:

  • Do not damage the inner surface or piston seal groove of the rear disc brake cylinder.
  • Do not allow the nut to rotate. If the nut is accidentally allowed to rotate, return it to its original position.

4. INSTALL REAR DISC BRAKE PISTON

(a) Apply a light layer of lithium soap base glycol grease to the entire circumference of a new cylinder boot.

*1

Cylinder Boot

*2

Rear Disc Brake Piston

Lithium Soap Base Glycol Grease

(b) Apply a light layer of lithium soap base glycol grease to the contact surfaces of the rear disc brake piston.

(c) Install the cylinder boot to the rear disc brake piston.

NOTICE:

The front and back sides of the cylinder boot are different. Make sure not to install the cylinder boot backwards.

*a

Front Side

*b

Back Side

(d) Install the rear disc brake piston to the rear disc brake cylinder assembly.

NOTICE:

  • Install the rear disc brake cylinder LH so that its portions marked (A) fit into the indentations of the rear disc brake piston.
  • Do not forcibly install the rear disc brake piston into the rear disc brake cylinder assembly.

*a

Indentations

(e) Install the cylinder boot to the rear disc brake cylinder assembly as shown in the illustration.

NOTICE:

  • Do not damage the cylinder boot.
  • Securely install the cylinder boot into the groove of the rear disc brake cylinder assembly and groove of the rear disc brake piston.

*1

Cylinder Boot

*2

Rear Disc Brake Cylinder Assembly

*3

Rear Disc Brake Piston
    Inspection
    INSPECTION PROCEDURE 1. INSPECT PAD LINING THICKNESS (a) Using a ruler, measure the rear disc brake pad lining thickness. Standard Thickness: 9.5 mm (0.374 in.) Minimum Thickne ...

    Installation
    INSTALLATION CAUTION / NOTICE / HINT HINT: Use the same procedure for the RH side and LH side. The following procedure is for the LH side. PROCEDURE 1. INSTALL REAR DISC ...

    Other materials:

    Toyota CH-R Service Manual > Lighting System: Freeze Frame Data
    FREEZE FRAME DATA FREEZE FRAME DATA (for LED Headlight) (a) Whenever a lighting system DTC is stored, the headlight ECU sub-assembly LH stores the current vehicle state as freeze frame data. CHECK FREEZE FRAME DATA (for LED Headlight) (a) Connect the Techstream to the DLC3. (b) Turn the ignit ...

    Toyota CH-R Service Manual > Can Communication System: Check Bus 3 Line for Short to +B
    DESCRIPTION There may be a short circuit between one of the CAN bus lines and +B when no resistance exists between terminal 6 (CA3H) of the central gateway ECU (network gateway ECU) and terminal 16 (BAT) of the DLC3, or terminal 21 (CA3L) of the central gateway ECU (network gateway ECU) and t ...

    Toyota C-HR (AX20) 2023-2025 Owner's Manual

    Toyota CH-R Owners Manual

    Toyota CH-R Service Manual

    © 2017-2025 Copyright www.tochr.net
    0.0125