Toyota CH-R Service Manual: Registration

Toyota CH-R Service Manual / Door Lock / Wireless Door Lock Control System(w/o Smart Key System) / Registration

REGISTRATION

CAUTION / NOTICE / HINT

HINT:

  • Register a new recognition code when replacing the door control transmitter assembly or the door control and tire pressure monitoring system receiver assembly.
  • Add mode is used to retain the codes that have already been registered while registering a new recognition code. This mode is used when adding a door control transmitter assembly.
  • Rewrite mode is used to clear all the previously registered codes and register only new recognition codes. This mode is used when exchanging the door control transmitter assembly or the door control and tire pressure monitoring system receiver assembly with a new one.
  • Confirmation mode is used to confirm how many recognition codes have already been registered before additional registration of a recognition code.
  • Prohibition mode is used to clear all the registered codes and cancel the wireless door lock function. Use this mode when the door control transmitter assembly is lost.
  • All of the steps in the following registration procedure must be performed in sequential order continuously.

PROCEDURE

1. REGISTRATION OF RECOGNITION CODE (USING TECHSTREAM)

(a) Connect the Techstream to the DLC3.

(b) Turn the ignition switch to ON.

(c) Turn the Techstream on.

(d) Enter the following menus: Body Electrical / Main Body / Utility / Wireless Code Registration.

Body Electrical > Main Body > Utility

Tester Display

Wireless Code Registration

(e) Select either add or rewrite mode according to the Techstream display.

(f) The number of registered codes is indicated.

(g) Registration of the door control transmitter assembly

(1) If either add mode or rewrite mode has been selected, press the lock and unlock switches on the door control transmitter assembly simultaneously.

(2) Within 3 seconds of releasing the lock and unlock switches, press either of the switches on the door control transmitter assembly.

NOTICE:

  • Do not press the lock and unlock switches simultaneously for more than 1.5 seconds.
  • Perform this operation within 1 meter of the driver seat to register the door control transmitter assembly.
  • Do not push other door control transmitter assembly switches during the door control transmitter assembly registration process.

(3) The main body ECU (multiplex network body ECU) automatically performs the power door lock/unlock operation once in order to indicate whether registration has been completed correctly or not.

(4) If continuing registration, the next recognition code must be registered in the door control transmitter assembly within 30 seconds.

HINT:

Up to 4 recognition codes can be registered.

(h) Completing the registration mode.

(1) Registration mode will end when any of the following occurs:

  • 30 seconds or more have elapsed after a code is registered.
  • The Techstream is used to finish registration.
  • The Techstream is disconnected.
  • The ignition switch is turned off.

(i) Perform the following after registration is completed.

(1) Perform the wireless door lock control operation check.

Click here

HINT:

If the wireless door lock control does not operate, perform the registration procedure again.

    Operation Check
    OPERATION CHECK NOTICE WHEN CHECKING THE FOLLOWING (a) Wireless door lock/unlock function: This wireless door lock control function operates only when the following 3 conditions are met: (1) The ...

    Customize Parameters
    CUSTOMIZE PARAMETERS CUSTOMIZE WIRELESS DOOR LOCK CONTROL SYSTEM (w/o Entry and Start System) HINT: The following items can be customized. NOTICE: When the customer requests a change in a ...

    Other materials:

    Toyota CH-R Service Manual > Rear Seat Outer Belt Assembly: Inspection
    INSPECTION PROCEDURE 1. INSPECT REAR SEAT 3 POINT TYPE OUTER BELT ASSEMBLY (a) Before installing the rear seat 3 point type outer belt assembly, check the ELR function. NOTICE: Do not disassemble the retractor. (1) When the inclination of the retractor is 15° or less, che ...

    Toyota CH-R Service Manual > Hazard Warning Switch: Inspection
    INSPECTION PROCEDURE 1. INSPECT HAZARD WARNING SIGNAL SWITCH ASSEMBLY (a) Check the resistance. (1) Measure the resistance according to the value(s) in the table below. Standard Resistance: Tester Connection Condition Specified ...

    Toyota CH-R Owners Manual

    Toyota CH-R Service Manual

    © 2017-2024 Copyright www.tochr.net
    0.0092