Toyota CH-R Service Manual: Data List / Active Test

Toyota CH-R Service Manual / Window / Glass / Power Window Control System / Data List / Active Test

DATA LIST / ACTIVE TEST

DATA LIST

HINT:

Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

(a) Connect the Techstream to the DLC3.

(b) Turn the ignition switch to ON.

(d) Enter the following menus: Body Electrical / (desired system) / Data List.

(e) Read the Data List according to the display on the Techstream.

Body Electrical > Master Switch > Data List

Tester Display	Measurement Item	Range	Normal Condition	Diagnostic Note
D Door P/W Auto SW	Driver door power window auto switch signal	OFF or ON	OFF: Driver door power window auto up or auto down switch not being operated ON: Driver door power window auto up or auto down switch being operated	-
P Door P/W Auto SW	Front passenger door power window auto switch signal	OFF or ON	OFF: Front passenger door power window auto up or auto down switch not being operated ON: Front passenger door power window auto up or auto down switch being operated	-
RR Door P/W Auto SW	Rear RH door power window auto switch signal	OFF or ON	OFF: Rear RH door power window auto up or auto down switch not being operated ON: Rear RH door power window auto up or auto down switch being operated	-
RL Door P/W Auto SW	Rear LH door power window auto switch signal	OFF or ON	OFF: Rear LH door power window auto up or auto down switch not being operated ON: Rear LH door power window auto up or auto down switch being operated	-
P Door P/W Up SW	Front passenger door power window manual up switch signal	OFF or ON	OFF: Front passenger door power window manual up switch not being operated ON: Front passenger door power window manual up switch being operated	-
RR Door P/W up switch	Rear RH door power window manual up switch signal	OFF or ON	OFF: Rear RH door power window manual up switch not being operated ON: Rear RH door power window manual up switch being operated	-
RL Door P/W up switch	Rear LH door power window manual up switch signal	OFF or ON	OFF: Rear LH door power window manual up switch not being operated ON: Rear LH door power window manual up switch being operated	-
P Door P/W Down SW	Front passenger door power window manual down switch signal	OFF or ON	OFF: Front passenger door power window manual down switch not being operated ON: Front passenger door power window manual down switch being operated	-
RR Door P/W Down SW	Rear RH door power window manual down switch signal	OFF or ON	OFF: Rear RH door power window manual down switch not being operated ON: Rear RH door power window manual down switch being operated	-
RL Door P/W Down SW	Rear LH door power window manual down switch signal	OFF or ON	OFF: Rear LH door power window manual down switch not being operated ON: Rear LH door power window manual down switch being operated	-
Window Lock Switch Status	Window lock switch signal	OFF or ON	OFF: Window lock switch off (not pushed in) ON: Window lock switch on (pushed in)	-
Number of Trouble Codes	Number of trouble codes	Min.: 0 or Max.: 255	Number of stored DTCs are displayed	-

Body Electrical > D-Door Motor > Data List

Tester Display	Measurement Item	Range	Normal Condition	Diagnostic Note
D Door P/W Auto SW	Driver door power window auto switch signal	OFF or ON	OFF: Driver door power window auto up or auto down switch not being operated ON: Driver door power window auto up or auto down switch being operated	-
D Door P/W Up SW	Driver door power window manual up switch signal	OFF or ON	OFF: Driver door power window manual up switch not being operated ON: Driver door power window manual up switch being operated	-
D Door P/W Down SW	Driver door power window manual down switch signal	OFF or ON	OFF: Driver door power window manual down switch not being operated ON: Driver door power window manual down switch being operated	-
Glass Position (Close-1/4)	Margin for jam protection triggering force of power window within range of fully closed to 1/4 open power window position	OK or Caution	OK: Normal manual up operation Caution: Jam detected in the specified range	Caution is displayed only when the power window ECU built into the power window regulator motor assembly detects a jam.
Glass Position (1/4-2/4)	Margin for jam protection triggering force of power window within range of 1/4 to 1/2 open power window position	OK or Caution	OK: Normal manual up operation Caution: Jam detected in the specified range	Caution is displayed only when the power window ECU built into the power window regulator motor assembly detects a jam.
Glass Position (2/4-3/4)	Margin for jam protection triggering force of power window within range of 1/2 to 3/4 open power window position	OK or Caution	OK: Normal manual up operation Caution: Jam detected in the specified range	Caution is displayed only when the power window ECU built into the power window regulator motor assembly detects a jam.
Glass Position (3/4-Open)	Margin for jam protection triggering force of power window within range of 3/4 to fully open power window position	OK or Caution	OK: Normal manual up operation Caution: Jam detected in the specified range	Caution is displayed only when the power window ECU built into the power window regulator motor assembly detects a jam.
D Window Auto Up	Auto up operation using the multiplex network master switch assembly	OFF or ON	Customize setting displayed	-
D Window Auto Down	Auto down operation using the multiplex network master switch assembly	OFF or ON	Customize setting displayed	-
Number of Trouble Codes	Number of trouble codes	Min.: 0 or Max.: 255	Number of stored DTCs are displayed	-

Body Electrical > P-Door Motor > Data List

Tester Display	Measurement Item	Range	Normal Condition	Diagnostic Note
P Door P/W Auto SW	Front passenger door power window auto switch signal	OFF or ON	OFF: Front passenger door power window auto up or auto down switch not being operated ON: Front passenger door power window auto up or auto down switch being operated	-
P Door P/W Up SW	Front passenger door power window manual up switch signal	OFF or ON	OFF: Front passenger door power window manual up switch not being operated ON: Front passenger door power window manual up switch being operated	-
P Door P/W Down SW	Front passenger door power window manual down switch signal	OFF or ON	OFF: Front passenger door power window manual down switch not being operated ON: Front passenger door power window manual down switch being operated	-
Glass Position (Close-1/4)	Margin for jam protection triggering force of power window within range of fully closed to 1/4 open power window position	OK or Caution	OK: Normal manual up operation Caution: Jam detected in the specified range	Caution is displayed only when the power window ECU built into the power window regulator motor assembly detects a jam.
Glass Position (1/4-2/4)	Margin for jam protection triggering force of power window within range of 1/4 to 1/2 open power window position	OK or Caution	OK: Normal manual up operation Caution: Jam detected in the specified range	Caution is displayed only when the power window ECU built into the power window regulator motor assembly detects a jam.
Glass Position (2/4-3/4)	Margin for jam protection triggering force of power window within range of 1/2 to 3/4 open power window position	OK or Caution	OK: Normal manual up operation Caution: Jam detected in the specified range	Caution is displayed only when the power window ECU built into the power window regulator motor assembly detects a jam.
Glass Position (3/4-Open)	Margin for jam protection triggering force of power window within range of 3/4 to fully open power window position	OK or Caution	OK: Normal manual up operation Caution: Jam detected in the specified range	Caution is displayed only when the power window ECU built into the power window regulator motor assembly detects a jam.
P Window Auto Up	Auto up operation using the power window regulator switch assembly	OFF or ON	Customize setting displayed	-
P Window Auto Up From Driver	Remote auto up operation using the multiplex network master switch assembly	OFF or ON	Customize setting displayed	-
P Window Auto Down	Auto down operation using the power window regulator switch assembly	OFF or ON	Customize setting displayed	-
P Window Auto Down From Driver	Remote auto down operation using the multiplex network master switch assembly	OFF or ON	Customize setting displayed	-
Number of Trouble Codes	Number of trouble codes	Min.: 0 or Max.: 255	Number of stored DTCs are displayed	-

Body Electrical > RL-Door Motor > Data List

Tester Display	Measurement Item	Range	Normal Condition	Diagnostic Note
RL Door P/W Auto SW	Rear LH door power window auto switch signal	OFF or ON	OFF: Rear LH door power window auto up or auto down switch not being operated ON: Rear LH door power window auto up or auto down switch being operated	-
RL Door P/W Up SW	Rear LH door power window manual up switch signal	OFF or ON	OFF: Rear LH door power window manual up switch not being operated ON: Rear LH door power window manual up switch being operated	-
RL Door P/W Down SW	Rear LH door power window manual down switch signal	OFF or ON	OFF: Rear LH door power window manual down switch not being operated ON: Rear LH door power window manual down switch being operated	-
Glass Position (Close-1/4)	Margin for jam protection triggering force of power window within range of fully closed to 1/4 open power window position	OK or Caution	OK: Normal manual up operation Caution: Jam detected in the specified range	Caution is displayed only when the power window ECU built into the power window regulator motor assembly detects a jam.
Glass Position (1/4-2/4)	Margin for jam protection triggering force of power window within range of 1/4 to 1/2 open power window position	OK or Caution	OK: Normal manual up operation Caution: Jam detected in the specified range	Caution is displayed only when the power window ECU built into the power window regulator motor assembly detects a jam.
Glass Position (2/4-3/4)	Margin for jam protection triggering force of power window within range of 1/2 to 3/4 open power window position	OK or Caution	OK: Normal manual up operation Caution: Jam detected in the specified range	Caution is displayed only when the power window ECU built into the power window regulator motor assembly detects a jam.
Glass Position (3/4-Open)	Margin for jam protection triggering force of power window within range of 3/4 to fully open power window position	OK or Caution	OK: Normal manual up operation Caution: Jam detected in the specified range	Caution is displayed only when the power window ECU built into the power window regulator motor assembly detects a jam.
RL Window Auto Up	Auto up operation using the rear power window regulator switch assembly (for LH door)	OFF or ON	Customize setting displayed	-
RL Window Auto Up From Driver	Remote auto up operation using the multiplex network master switch assembly	OFF or ON	Customize setting displayed	-
RL Window Auto Down	Auto down operation using the rear power window regulator switch assembly (for LH door)	OFF or ON	Customize setting displayed	-
RL Window Auto Down From Driver	Remote auto down operation using the multiplex network master switch assembly	OFF or ON	Customize setting displayed	-
Number of Trouble Codes	Number of trouble codes	Min.: 0 or Max.: 255	Number of stored DTCs are displayed	-

Body Electrical > RR-Door Motor > Data List

Tester Display	Measurement Item	Range	Normal Condition	Diagnostic Note
RR Door P/W Auto SW	Rear RH door power window auto switch signal	OFF or ON	OFF: Rear RH door power window auto up or auto down switch not being operated ON: Rear RH door power window auto up or auto down switch being operated	-
RR Door P/W Up SW	Rear RH door power window manual up switch signal	OFF or ON	OFF: Rear RH door power window manual up switch not being operated ON: Rear RH door power window manual up switch being operated	-
RR Door P/W Down SW	Rear RH door power window manual down switch signal	OFF or ON	OFF: Rear RH door power window manual down switch not being operated ON: Rear RH door power window manual down switch being operated	-
Glass Position (Close-1/4)	Margin for jam protection triggering force of power window within range of 1/4 to 1/2 open power window position	OK or Caution	OK: Normal manual up operation Caution: Jam detected in the specified range	Caution is displayed only when the power window ECU built into the power window regulator motor assembly detects a jam.
Glass Position (1/4-2/4)	Margin for jam protection triggering force of power window within range of 1/2 to 3/4 open power window position	OK or Caution	OK: Normal manual up operation Caution: Jam detected in the specified range	Caution is displayed only when the power window ECU built into the power window regulator motor assembly detects a jam.
Glass Position (2/4-3/4)	Margin for jam protection triggering force of power window within range of 3/4 to fully open power window position	OK or Caution	OK: Normal manual up operation Caution: Jam detected in the specified range	Caution is displayed only when the power window ECU built into the power window regulator motor assembly detects a jam.
Glass Position (3/4-Open)	Margin for jam protection triggering force of power window within range of 3/4 to fully open power window position	OK or Caution	OK: Normal manual up operation Caution: Jam detected in the specified range	Caution is displayed only when the power window ECU built into the power window regulator motor assembly detects a jam.
RR Window Auto Up	Auto up operation using the rear power window regulator switch assembly (for RH door)	OFF or ON	Customize setting displayed	-
RR Window Auto Up From Driver	Remote auto up operation using the multiplex network master switch assembly	OFF or ON	Customize setting displayed	-
RR Window Auto Down	Auto down operation using the rear power window regulator switch assembly (for RH door)	OFF or ON	Customize setting displayed	-
RR Window Auto Down From Driver	Remote auto down operation using the multiplex network master switch assembly	OFF or ON	Customize setting displayed	-
Number of Trouble Codes	Number of trouble codes	Min.: 0 or Max.: 255	Number of stored DTCs are displayed	-

Body Electrical > Main Body > Data List

Tester Display	Measurement Item	Range	Normal Condition	Diagnostic Note
IG SW	Ignition switch status	OFF or ON	OFF: Ignition switch off ON: Ignition switch ON	"OFF" is also displayed for this item when the ignition switch ACC.
Door Key SW-Lock	Driver door door lock/unlock switch lock signal (key-linked lock switch)	OFF or ON	OFF: Driver door key cylinder not turned ON: Driver door key cylinder turned to lock position	-
D Door Key SW-UL	Driver door door lock/unlock switch unlock signal (key-linked unlock switch)	OFF or ON	OFF: Driver door key cylinder not turned ON: Driver door key cylinder turned to unlock position	-
FR Door Courtesy SW	Front door courtesy light switch assembly (for RH) signal	OFF or ON	OFF: Front door RH closed ON: Front door RH open	-
FL Door Courtesy SW	Front door courtesy light switch assembly (for LH) signal	OFF or ON	OFF: Front door LH closed ON: Front door LH open	-
Door Key P/W Up	Door key linked power window up	OFF or ON	Customize setting displayed	-
Door Key P/W Down	Door key linked power window down	OFF or ON	Customize setting displayed	-
P/W Down W/ Transmit	Wireless transmitter linked power window down	OFF or ON	Customize setting displayed	-
P/W Wireless Ope Buzz	Power window buzzer answer-back of wireless function	OFF or ON	Customize setting displayed	-
Window Open Warning	Window open warning	OFF or ON	Customize setting displayed	-
Communication D-Door Motor	Connection status between power window regulator motor assembly (for driver door) and main body ECU (multiplex network body ECU)	STOP or OK	STOP: Communication stopped OK: Normal communication	-
Communication P-Door Motor	Connection status between power window regulator motor assembly (for front passenger door) and main body ECU (multiplex network body ECU)	STOP or OK	STOP: Communication stopped OK: Normal communication	-
Communication RR-Door Motor	Connection status between power window regulator motor assembly (for rear RH door) and main body ECU (multiplex network body ECU)	STOP or OK	STOP: Communication stopped OK: Normal communication	-
Communication RL-Door Motor	Connection status between power window regulator motor assembly (for rear LH door) and main body ECU (multiplex network body ECU)	STOP or OK	STOP: Communication stopped OK: Normal communication	-
Communication Master SW	Connection status between multiplex network master switch assembly and main body ECU (multiplex network body ECU)	STOP or OK	STOP: Communication stopped OK: Normal communication	-

ACTIVE TEST

HINT:

Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

(a) Connect the Techstream to the DLC3.

(b) Turn the ignition switch to ON.

(d) Enter the following menus: Body Electrical / (desired system) / Active Test.

(e) Perform the Active Test, according to the display on the Techstream.

CAUTION:

Be careful to avoid injuries as this test causes vehicle parts to move. During the Active Test, the jam protection function will not operate.

Body Electrical > D-Door Motor > Active Test

Tester Display	Measurement Item	Control Range	Diagnostic Note
Power Window	Power window	OFF / DOWN / UP	-

Body Electrical > P-Door Motor > Active Test

Tester Display	Measurement Item	Control Range	Diagnostic Note
Power Window	Power window	OFF / DOWN / UP	-

Body Electrical > RL-Door Motor > Active Test

Tester Display	Measurement Item	Control Range	Diagnostic Note
Power Window	Power window	OFF / DOWN / UP	-

Body Electrical > RR-Door Motor > Active Test

Tester Display	Measurement Item	Control Range	Diagnostic Note
Power Window	Power window	OFF / DOWN / UP	-

Fail-safe Chart

FAIL-SAFE CHART PULSE FAILURE (a) If a pulse sensor built into the power window regulator motor assembly malfunctions, the following power window operations will be prohibited. Multiplex Network ...

Diagnostic Trouble Code Chart

DIAGNOSTIC TROUBLE CODE CHART Power Window Control System DTC No. Detection Item Link B2311 Power Window Motor Malfunction ...

Other materials:

Toyota CH-R Service Manual > Rear Shock Absorber: Installation
INSTALLATION CAUTION / NOTICE / HINT HINT: Use the same procedure for the RH side and LH side. The following procedure is for the LH side. PROCEDURE 1. INSTALL REAR SUSPENSION SUPPORT ASSEMBLY (a) Secure the rear suspension support assembly in a vise using aluminum plates. N ...

Toyota CH-R Owners Manual > Driving procedures: Continuously variable transmission
Shifting the shift lever Vehicles without a smart key system: While the engine switch is in the "ON" position and the brake pedal depressed*, shift the shift lever while pushing the shift release button on the shift knob. Vehicles with a smart key system: While the engine swi ...