COMPONENTS
ILLUSTRATION
*1 |
FRONT BUMPER ASSEMBLY |
*2 |
FRONT FENDER MOULDING SUB-ASSEMBLY LH |
*3 |
FRONT FENDER MOULDING SUB-ASSEMBLY RH |
*4 |
RADIATOR COVER |
ILLUSTRATION
*A |
for USA and Canada |
- |
- |
*1 |
FOG LIGHT COVER LH |
*2 |
FOG LIGHT COVER RH |
*3 |
FRONT BUMPER EXTENSION LH |
*4 |
FRONT BUMPER EXTENSION MOUNTING BRACKET |
*5 |
FRONT BUMPER EXTENSION RH |
*6 |
FRONT BUMPER HOLE COVER |
*7 |
FRONT BUMPER SIDE MOUNTING BRACKET LH |
*8 |
FRONT BUMPER SIDE MOUNTING BRACKET RH |
*9 |
FRONT FENDER LINER RETAINER |
*10 |
RADIATOR GRILLE |
ILLUSTRATION
*A |
for USA and Canada |
- |
- |
*1 |
FRONT BUMPER LOWER COVER |
*2 |
INNER RADIATOR GRILLE |
*3 |
FRONT BUMPER COVER |
*4 |
GROMMET |
*5 |
OUTSIDE MOULDING RETAINER |
- |
- |
ILLUSTRATION
*A |
for USA and Canada |
- |
- |
*1 |
FRONT BUMPER ENERGY ABSORBER |
*2 |
FRONT BUMPER SIDE RETAINER LH |
*3 |
FRONT BUMPER SIDE RETAINER RH |
*4 |
FRONT ENERGY ABSORBER MOUNTING REINFORCEMENT |
*5 |
LOWER FRONT BUMPER ABSORBER |
*6 |
NO. 1 RADIATOR GRILLE RETAINER |
*7 |
NO. 1 RADIATOR TO SUPPORT SEAL |
- |
- |
N*m (kgf*cm, ft.*lbf): Specified torque |
- |
- |
ILLUSTRATION
*A |
for USA and Canada |
- |
- |
*1 |
FRONT BUMPER BRACKET LH |
*2 |
FRONT BUMPER BRACKET RH |
*3 |
FRONT BUMPER REINFORCEMENT |
*4 |
FRONT SIDE MEMBER BRACKET SUB-ASSEMBLY LH |
*5 |
FRONT SIDE MEMBER BRACKET SUB-ASSEMBLY RH |
*6 |
NO. 1 RADIATOR AIR GUIDE LH |
*7 |
NO. 1 RADIATOR AIR GUIDE RH |
*8 |
NO. 2 FRONT BUMPER REINFORCEMENT |
N*m (kgf*cm, ft.*lbf): Specified torque |
- |
- |
ILLUSTRATION
*A |
except USA and Canada |
- |
- |
*1 |
FOG LIGHT ASSEMBLY LH |
*2 |
FOG LIGHT ASSEMBLY RH |
*3 |
FOG LIGHT COVER LH |
*4 |
FOG LIGHT COVER RH |
ILLUSTRATION
*A |
except USA and Canada |
- |
- |
*1 |
FOG LIGHT ASSEMBLY LH |
*2 |
FOG LIGHT ASSEMBLY RH |
*3 |
FRONT BUMPER EXTENSION MOUNTING BRACKET |
*4 |
FRONT BUMPER HOLE COVER |
*5 |
FRONT BUMPER LOWER COVER |
*6 |
FRONT BUMPER SIDE MOUNTING BRACKET LH |
*7 |
FRONT BUMPER SIDE MOUNTING BRACKET RH |
*8 |
FRONT FENDER LINER RETAINER |
*9 |
INNER RADIATOR GRILLE |
*10 |
NO. 1 RADIATOR GRILLE MOULDING |
*11 |
FRONT BUMPER COVER |
*12 |
OUTSIDE MOULDING RETAINER |
*13 |
GROMMET |
- |
- |
ILLUSTRATION
*A |
except USA and Canada |
- |
- |
*1 |
FRONT BUMPER BRACKET LH |
*2 |
FRONT BUMPER BRACKET RH |
*3 |
FRONT BUMPER ENERGY ABSORBER |
*4 |
FRONT BUMPER REINFORCEMENT |
*5 |
FRONT BUMPER SIDE RETAINER LH |
*6 |
FRONT BUMPER SIDE RETAINER RH |
*7 |
FRONT SIDE MEMBER BRACKET SUB-ASSEMBLY LH |
*8 |
FRONT SIDE MEMBER BRACKET SUB-ASSEMBLY RH |
*9 |
LOWER FRONT BUMPER ABSORBER |
*10 |
NO. 1 RADIATOR AIR GUIDE LH |
*11 |
NO. 1 RADIATOR AIR GUIDE RH |
*12 |
NO. 1 RADIATOR GRILLE RETAINER |
*13 |
NO. 1 RADIATOR TO SUPPORT SEAL |
*14 |
NO. 2 FRONT BUMPER REINFORCEMENT |
N*m (kgf*cm, ft.*lbf): Specified torque |
- |
- |
Toyota CH-R Service Manual > Vehicle Stability Control System: ABS Warning Light does not Come ON
DESCRIPTION
The skid control ECU (brake actuator assembly) is connected to the combination
meter assembly via CAN communication.
CAUTION / NOTICE / HINT
NOTICE:
When replacing the skid control ECU (brake actuator assembly), perform system
variant learning.
Click here
PROCEDURE
...
Toyota CH-R Service Manual > Power Window Control System: Terminals Of Ecu
TERMINALS OF ECU
CHECK MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY
(a) Disconnect the J6 multiplex network master switch assembly connector.
(b) Measure the voltage and resistance according to the value(s) in the table
below.
HINT:
Measure the values on the wire harness side with the connector ...