Toyota CH-R Owners Manual: Rear door child-protector lock

Toyota CH-R Owners Manual / Operation of each component / Opening, closing and locking the doors / Side doors / Rear door child-protector lock

The door cannot be opened from inside the vehicle when the lock is set.

Unlock
Lock

These locks can be set to prevent children from opening the rear doors. Push down on each rear door switch to lock both rear doors.

Toyota CH-R. Opening, closing and locking the doors

■Switching the door unlock function (vehicles with a smart key system) It is possible to set which doors the entry function unlocks using the wireless remote control.

1. Turn the engine switch off.

2. When the indicator light on the key surface is not on, press and hold for approximately 5 seconds while pressing and holding .

The setting changes each time an operation is performed, as shown below.

(When changing the setting continuously, release the buttons, wait for at least 5 seconds, and repeat step 2.)

Multi-information display	Unlocking function	Beep
	Holding the driver's door handle unlocks only the driver's door.	Exterior: Beeps 3 times Interior: Pings once
	Holding the front passenger's door handle unlocks all the doors.	Exterior: Beeps 3 times Interior: Pings once
	Holding a door handle unlocks all the doors.	Exterior: Beeps twice Interior: Pings once

■Open door warning buzzer If a door or the back door is not fully closed, a buzzer will sound when the vehicle speed reaches 3 mph (5 km/h).

The open door(s) or back door is indicated on the multi-information display.

■Conditions affecting the operation of the smart key system or wireless remote control

Vehicles without a smart key system

Vehicles with a smart key system

■Customization Settings (e.g. unlocking function using a key) can be changed.

WARNING

■To prevent an accident Observe the following precautions while driving the vehicle.

Failure to do so may result in a door opening and an occupant falling out, resulting in death or serious injury.

Ensure that all doors are properly closed and locked.
Do not pull the inside handle of the doors while driving.
Be especially careful for the front doors, as the doors may be opened even if the inside lock buttons are in locked position.
Set the rear door child-protector locks when children are seated in the rear seats.

■When opening or closing a door Check the surroundings of the vehicle such as whether the vehicle is on an incline, whether there is enough space for a door to open and whether a strong wind is blowing.

When opening or closing the door, hold the door handle tightly to prepare for any unpredictable movement.

■When using the wireless remote control or key and operating the power windows Operate the power window after checking to make sure that there is no possibility of any passenger having any of their body parts caught in the side window. Also, do not allow children to operate the wireless remote control or key. It is possible for children and other passengers to get caught in the power window.

■When closing the rear door Take extra care to prevent your fingers, etc., from being caught. Failure to do so may result in death or serious injury.

Toyota CH-R. Opening, closing and locking the doors

Unlocking and locking the doors from the inside

Door lock switches Locks all the doors Unlocks all the doors Inside lock buttons Locks the door Unlocks the door The front doors can be opened by pulling the inside handle even i ...

Back door

The back door can be locked/unlocked and opened by the following procedures. Unlocking and locking the back door Entry function (vehicles with a smart key system) Press the button to unlock th ...

Other materials:

Toyota CH-R Service Manual > Windshield Outside Moulding: Components
COMPONENTS ILLUSTRATION *1 NO. 1 WINDSHIELD OUTSIDE MOULDING CLIP *2 NO. 3 WINDSHIELD OUTSIDE MOULDING CLIP *3 WINDSHIELD OUTSIDE MOULDING *4 WINDSHIELD GLASS SUB-ASSEMBLY ● ...

Toyota CH-R Service Manual > Toyota Entune System: DCM Data Signal Circuit between Navigation ECU and DCM
DESCRIPTION This circuit is used to send and receive signals between the DCM (Telematics Transceiver) and radio and display receiver assembly. WIRING DIAGRAM PROCEDURE 1. CHECK VEHICLE TYPE (a) Check vehicle type. Result Proceed to ...