Toyota CH-R Service Manual: Steering Pad Switch Circuit

Toyota CH-R Service Manual / Audio / Video / Audio And Visual System(for Radio Receiver Type) / Steering Pad Switch Circuit

DESCRIPTION

This circuit sends an operation signal from the steering pad switch assembly to the radio receiver assembly.

If there is an open in the circuit, the audio system cannot be operated using the steering pad switch assembly.

If there is a short in the circuit, the same condition as when a switch is continuously depressed occurs. Therefore, the radio receiver assembly cannot be operated using the steering pad switch assembly, also the radio receiver assembly itself will not function.

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

The vehicle is equipped with a Supplemental Restraint System (SRS) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precaution for Supplemental Restraint System.

Click here

PROCEDURE

1.

CHECK HARNESS AND CONNECTOR (STEERING PAD SWITCH SIGNAL)

(a) Disconnect the F47 radio receiver assembly connector.

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

F47-21 (SW1) - F47-23 (SWG)

No switch pushed

95 to 105 kΩ

Seek+ switch pushed

Below 2.5 Ω

Seek- switch pushed

313 to 345 Ω

Volume+ switch pushed

950 to 1050 Ω

Volume- switch pushed

2955 to 3265 Ω

F47-22 (SW2) - F47-23 (SWG)

No switch pushed

95 to 105 kΩ

MODE switch pushed

Below 2.5 Ω

On hook switch pushed

313 to 345 Ω

Off hook switch pushed

950 to 1050 Ω

Voice switch pushed

2955 to 3265 Ω
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.

INSPECT STEERING PAD SWITCH ASSEMBLY

(a) Remove the steering pad switch assembly.

Click here

(b) Inspect the steering pad switch assembly

Click here

NG

REPLACE STEERING PAD SWITCH ASSEMBLY

OK

3.

INSPECT SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY

(a) Remove the spiral cable with sensor sub-assembly.

Click here

(b) Inspect the spiral cable with sensor sub-assembly.

Click here

NOTICE:

  • Press and hold the lock located in the center of the spiral cable with sensor sub-assembly to rotate the spiral cable with sensor sub-assembly.
  • The spiral cable with sensor sub-assembly is an important part of the SRS airbag system. Incorrect removal or installation of the spiral cable with sensor sub-assembly may prevent the airbag from deploying.
  • As the spiral cable with sensor sub-assembly may break, do not rotate the spiral cable with sensor sub-assembly more than the specified amount.
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (RADIO RECEIVER ASSEMBLY - SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY - BODY GROUND)
NG

REPLACE SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY

    Vehicle Speed Signal Circuit between Radio Receiver and Combination Meter
    DESCRIPTION for Automatic Sound Levelizer (ASL): This circuit is necessary for the Automatic Sound Levelizer (ASL) built into the radio receiver assembly. The Automatic Sound Levelize ...

    Illumination Circuit
    DESCRIPTION Power is supplied to the radio receiver assembly and steering pad switch assembly illumination when the light control switch is in the tail or head position. WIRING DIAGRAM CAUTION ...

    Other materials:

    Toyota CH-R Service Manual > Rear Spoiler: Installation
    INSTALLATION PROCEDURE 1. INSTALL REAR SPOILER ASSEMBLY (a) Engage the clips to install the rear spoiler assembly as shown in the illustration. Install in this Direction (b) Install the 8 nuts. Torque: 6.0 N·m {61 kgf·cm, 53 in·lbf} (c) Connect the connecto ...

    Toyota CH-R Service Manual > Audio And Visual System(for Radio Receiver Type): Terminals Of Ecu
    TERMINALS OF ECU Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition F47-4 (MACC) - F48-7 (GND1) B - LA Microphone power supply Ignition switch off ...

    Toyota CH-R Owners Manual

    Toyota CH-R Service Manual

    © 2017-2025 Copyright www.tochr.net
    0.0112