Toyota CH-R Service Manual: Dtc Check / Clear

Toyota CH-R Service Manual / Theft Deterrent / Keyless Entry / Smart Key System(for Start Function) / Dtc Check / Clear

DTC CHECK / CLEAR

NOTICE:

When using the Techstream with the engine switch off, connect the Techstream to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the Techstream and the vehicle begins. Then select the vehicle type under manual mode and enter the following menus: Body Electrical / Smart Key. While using the Techstream, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the Techstream and the vehicle.

CHECK FOR DTC (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (POWER SOURCE CONTROL))

(a) Connect the Techstream to the DLC3.

(b) Turn the engine switch on (IG).

(c) Turn the Techstream on.

(d) Enter the following menus: Body Electrical / Power Source Control / Trouble Codes.

Body Electrical > Power Source Control > Trouble Codes

(e) Check for DTCs.

CHECK FOR DTC (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (ENTRY&START))

(a) Connect the Techstream to the DLC3.

(b) Turn the engine switch on (IG).

(c) Turn the Techstream on.

(d) Enter the following menus: Body Electrical / Smart Key / Trouble Codes.

Body Electrical > Smart Key > Trouble Codes

(e) Check for DTCs.

CHECK FOR DTC (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (STARTING CONTROL))

(a) Connect the Techstream to the DLC3.

(b) Turn the engine switch on (IG).

(c) Turn the Techstream on.

(d) Enter the following menus: Body Electrical / Starting Control / Trouble Codes.

Body Electrical > Starting Control > Trouble Codes

(e) Check for DTCs.

CLEAR DTC (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (POWER SOURCE CONTROL))

(a) Connect the Techstream to the DLC3.

(b) Turn the engine switch on (IG).

(c) Turn the Techstream on.

(d) Enter the following menus: Body Electrical / Power Source Control / Trouble Codes.

Body Electrical > Power Source Control > Clear DTCs

(e) Clear the DTCs.

CLEAR DTC (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (ENTRY&START))

(a) Connect the Techstream to the DLC3.

(b) Turn the engine switch on (IG).

(c) Turn the Techstream on.

(d) Enter the following menus: Body Electrical / Smart Key / Trouble Codes.

Body Electrical > Smart Key > Clear DTCs

(e) Clear the DTCs.

CLEAR DTC (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (STARTING CONTROL))

(a) Connect the Techstream to the DLC3.

(b) Turn the engine switch on (IG).

(c) Turn the Techstream on.

(d) Enter the following menus: Body Electrical / Starting Control / Trouble Codes.

Body Electrical > Starting Control > Clear DTCs

(e) Clear the DTCs.

    Terminals Of Ecu
    TERMINALS OF ECU CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (a) Disconnect the M66, M67 and F1 certification ECU (smart key ECU assembly) connectors. (b) Measure the voltage and resistanc ...

    Data List / Active Test
    DATA LIST / ACTIVE TEST DATA LIST HINT: Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any part ...

    Other materials:

    Toyota CH-R Service Manual > Power Steering System: Error in Matching of ECUs (C1567)
    DESCRIPTION Based on the steering sensor signal, the power steering ECU assembly determines if the correct type of steering sensor is installed. DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Return-t ...

    Toyota CH-R Service Manual > Wiper And Washer System: Terminals Of Ecu
    TERMINALS OF ECU CHECK WINDSHIELD WIPER RELAY ASSEMBLY (w/ Rain Sensor) (a) Disconnect the F56 windshield wiper relay assembly connector. (1) Measure the voltage and resistance on the wire harness side connector according to the value(s) in the table below. Terminal No. (Symbol ...

    Toyota CH-R Owners Manual

    Toyota CH-R Service Manual

    © 2017-2025 Copyright www.tochr.net
    0.0167