Toyota CH-R Service Manual: On-vehicle Inspection
ON-VEHICLE INSPECTION
CAUTION / NOTICE / HINT
CAUTION:
Be sure to correctly follow the removal and installation procedures for the instrument panel passenger airbag assembly.
PROCEDURE
1. INSPECT INSTRUMENT PANEL PASSENGER AIRBAG ASSEMBLY (for Vehicle not Involved in Collision)
(a) Perform a diagnostic system check.
Click here .gif)
(b) Visually check for defects with the instrument panel passenger airbag assembly installed to the vehicle.
HINT:
The defects are as follows:
- Cuts on the instrument panel safety pad sub-assembly around the instrument panel passenger airbag assembly
- Small cracks on the instrument panel safety pad sub-assembly around the instrument panel passenger airbag assembly
- Significant discoloration on the instrument panel safety pad sub-assembly around the instrument panel passenger airbag assembly
OK:
No defects are found.
If any defects are found, replace the No. 1 instrument panel sub-assembly with a new one.
2. INSPECT INSTRUMENT PANEL PASSENGER AIRBAG ASSEMBLY (for Vehicle Involved in Collision and Airbag not Deployed)
(a) Perform a diagnostic system check.
Click here
(b) Visually check for defects with the instrument panel passenger airbag assembly removed from the vehicle.
HINT:
The defects are as follows:
- Cuts
- Small cracks
- Significant discoloration
- Cracks or other damage to the connector
- Deformation or cracks on the instrument panel safety pad sub-assembly or instrument panel reinforcement assembly
OK:
No defects are found.
If any defects are found, replace the instrument panel passenger airbag assembly, No. 1 instrument panel sub-assembly or instrument panel reinforcement assembly with a new one.
Components
COMPONENTS
ILLUSTRATION
*1
INSTRUMENT PANEL PASSENGER AIRBAG ASSEMBLY
*2
NO. 2 INSTRUMENT PANEL WIRE
...
Installation
INSTALLATION
PROCEDURE
1. INSTALL NO. 2 INSTRUMENT PANEL WIRE
(a) for Single Type:
(1) Connect the airbag connector of the No. 2 instrument panel wire to
the instrument panel pass ...
Other materials:
Toyota CH-R Service Manual > Blower Unit(for Denso Made): Disassembly
DISASSEMBLY
PROCEDURE
1. PRECAUTION
NOTICE:
Make sure to perform initialization after replacing the No. 1 blower damper servo
sub-assembly. If initialization is not performed, the air conditioner unit assembly
will not perform properly as the air conditioning amplifier assembly will not be
...
Toyota CH-R Service Manual > Smart Key System(for Start Function): Parts Location
PARTS LOCATION
ILLUSTRATION
*1
PARK/NEUTRAL POSITION SWITCH
*2
STARTER ASSEMBLY
*3
NO. 1 ENGINE ROOM RELAY BLOCK
- IG2-MAIN FUSE
- ECU-IG2 NO. 1 FUSE
- ST FUSE
- WIPER FUSE
- ST RELAY
*4
...
Toyota CH-R Owners Manual
- For safety and security
- Instrument cluster
- Operation of each component
- Driving
- Interior features
- Maintenance and care
- When trouble arises
- Vehicle specifications
- For owners
Toyota CH-R Service Manual
- Introduction
- Maintenance
- Audio / Video
- Cellular Communication
- Navigation / Multi Info Display
- Park Assist / Monitoring
- Brake (front)
- Brake (rear)
- Brake Control / Dynamic Control Systems
- Brake System (other)
- Parking Brake
- Axle And Differential
- Drive Shaft / Propeller Shaft
- K114 Cvt
- 3zr-fae Battery / Charging
- Networking
- Power Distribution
- Power Assist Systems
- Steering Column
- Steering Gear / Linkage
- Alignment / Handling Diagnosis
- Front Suspension
- Rear Suspension
- Tire / Wheel
- Tire Pressure Monitoring
- Door / Hatch
- Exterior Panels / Trim
- Horn
- Lighting (ext)
- Mirror (ext)
- Window / Glass
- Wiper / Washer
- Door Lock
- Heating / Air Conditioning
- Interior Panels / Trim
- Lighting (int)
- Meter / Gauge / Display
- Mirror (int)
- Power Outlets (int)
- Pre-collision
- Seat
- Seat Belt
- Supplemental Restraint Systems
- Theft Deterrent / Keyless Entry
0.0094