Toyota CH-R Service Manual: Side Airbag Sensor RH Circuit Malfunction (B1620/21)

Toyota CH-R Service Manual / Supplemental Restraint Systems / Airbag System / Side Airbag Sensor RH Circuit Malfunction (B1620/21)

DESCRIPTION

The side collision sensor RH circuit (bus 1) consists of the airbag sensor assembly, door side airbag sensor RH, No. 1 side airbag sensor RH and No. 2 side airbag sensor RH.

The door side airbag sensor RH, No. 1 side airbag sensor RH and No. 2 side airbag sensor RH detect impacts to the vehicle and send signals to the airbag sensor assembly to determine if the airbags and pretensioners should be deployed.

DTC B1620/21 is stored when a malfunction is detected in the No. 1 side airbag sensor RH.

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

Test Mode / Check Mode

B1620/21

Side Airbag Sensor RH Circuit Malfunction

Any of the following conditions is met:

  • No. 1 side airbag sensor RH malfunction
  • Airbag sensor assembly malfunction
  • No. 1 side airbag sensor RH
  • Airbag sensor assembly

Does not apply to test/check mode
DTC Detection Conditions:
 

Vehicle Condition

Pattern 1

Pattern 2

Diagnosis Condition

Ignition switch ON

○

○

Malfunction Status

No. 1 side airbag sensor RH malfunction

○

-

Airbag sensor assembly malfunction

-

○

Detection Time

-

-

Number of Trips

1 trip

1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.

WIRING DIAGRAM

Click here

CAUTION / NOTICE / HINT

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click here

PROCEDURE

1.

CHECK NO. 1 SIDE AIRBAG SENSOR RH

(a) Turn the ignition switch off.

*1

No. 1 Side Airbag Sensor LH

*2

Airbag Sensor Assembly

(b) Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

(c) Interchange the No. 1 side airbag sensor RH with LH and connect the connectors.

(d) Connect the cable to the negative (-) battery terminal.

(e) Clear the DTCs stored in memory.

Click here

Body Electrical > SRS Airbag > Clear DTCs

(f) Turn the ignition switch off.

(g) Turn the ignition switch ON, and wait for at least 60 seconds.

(h) Check for DTCs.

Click here

Body Electrical > SRS Airbag > Trouble Codes

HINT:

Codes other than DTCs B1620/21 and B1625/22 may be output at this time, but they are not related to this check.

Result

Proceed to

DTC B1620/21 is output.

A

DTC B1625/22 is output.

B

DTCs B1620/21 and B1625/22 are not output.

C

(i) Turn the ignition switch off.

(j) Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

(k) Return the No. 1 side airbag sensor RH and LH to their original positions and connect the connectors.

A

REPLACE AIRBAG SENSOR ASSEMBLY

B

REPLACE NO. 1 SIDE AIRBAG SENSOR RH

C

USE SIMULATION METHOD TO CHECK

    Center Airbag Sensor Assembly Malfunction (B1000/31)
    DESCRIPTION The airbag sensor assembly consists of the acceleration sensor, safing sensor, drive circuit, diagnosis circuit, ignition control, etc. If the airbag sensor assembly receives signals f ...

    Side Airbag Sensor Assembly No.2 (RH) (B162A/2A)
    DESCRIPTION The side collision sensor RH circuit (bus 2) consists of the airbag sensor assembly and floor side airbag sensor RH. The floor side airbag sensor RH detects impacts to the vehicle and ...

    Other materials:

    Toyota CH-R Service Manual > Integration Relay: Installation
    INSTALLATION PROCEDURE 1. INSTALL NO. 1 INTEGRATION RELAY (a) Connect the 2 connectors. (b) Engage the claws to install the No. 1 integration relay as shown in the illustration. Install in this Direction 2. INSTALL NO. 1 RELAY BLOCK COVER (a) Engage the claws to ...

    Toyota CH-R Service Manual > Air Conditioning System(for Automatic Air Conditioning System With Top-mounted Air Conditioner Pressure Sensor): Lost Communication with Front Panel LIN (B14B2)
    DESCRIPTION The air conditioning control assembly communicates with the air conditioning amplifier assembly via LIN communication. If the LIN communication system malfunctions, the air conditioning amplifier assembly does not operate even if the air conditioning control assembly is operated. ...

    Toyota CH-R Owners Manual

    Toyota CH-R Service Manual

    © 2017-2025 Copyright www.tochr.net
    0.0126