Toyota CH-R Service Manual: Customize Parameters
CUSTOMIZE PARAMETERS
CUSTOMIZE SEAT BELT WARNING SYSTEM
HINT:
The following items can be customized.
NOTICE:
- When the customer requests a change in a function, first make sure that the function can be customized.
- Be sure to make a note of the current settings before customizing.
- When troubleshooting a function, first make sure that the function is set to the default setting.
- These buzzers should be on for safe driving. Perform this procedure only if it is necessary to set the buzzer to off (disabled).
(a) Customizing with the Techstream
(1) Connect the Techstream to the DLC3.
(2) Turn the ignition switch to ON.
(3) Turn the Techstream on.
(4) Enter the following menus: Customize Setting / Warning.
(5) Select the setting by referring to the table below.
Warning|
Tester Display |
Description |
Default |
Setting |
ECU |
|---|---|---|---|---|
|
Driver Side Seatbelt Warning Buzzer |
Enables sounding of the driver seat belt warning buzzer |
ON |
0:OFF,1:ON |
Combination Meter Assembly |
|
Front Passenger Side Seatbelt Warning Buzzer |
Enables sounding of the front passenger seat belt warning buzzer |
ON |
0:OFF,1:ON |
Combination Meter Assembly |
|
Rear Seatbelt Warning Buzzer |
Function to sound the rear seat belt warning buzzer |
ON |
0:OFF,1:ON |
Combination Meter Assembly |
HINT:
These settings are only valid when the vehicle is driven at 20 km/h (12 mph) or more.
How To Proceed With Troubleshooting
CAUTION / NOTICE / HINT
HINT:
Use the following procedure to troubleshoot the seat belt warning system.
*: Use the Techstream.
PROCEDURE
1.
VEHICLE BROU ...
Problem Symptoms Table
PROBLEM SYMPTOMS TABLE
NOTICE:
When replacing the combination meter assembly, always replace it with a new one.
If a combination meter assembly which was installed to another vehicle is used,
th ...
Other materials:
Toyota CH-R Service Manual > 3zr-fae Coolant: Components
COMPONENTS
ILLUSTRATION
*1
RESERVE TANK CAP
*2
RADIATOR DRAIN COCK PLUG
*3
NO. 1 ENGINE UNDER COVER
-
-
N*m (kgf*cm, ft.*lbf): Specified torque
-
-
...
Toyota CH-R Service Manual > Brake Pedal: Installation
INSTALLATION
PROCEDURE
1. INSTALL BRAKE PEDAL PAD
(a) Install the brake pedal pad from the brake pedal support assembly.
2. INSTALL BRAKE PEDAL SUPPORT ASSEMBLY
(a) Install the nut to the brake pedal support assembly.
(b) Temporarily install the brake pedal support assembly with 2 n ...
Toyota CH-R Owners Manual
- For safety and security
- Instrument cluster
- Operation of each component
- Driving
- Interior features
- Maintenance and care
- When trouble arises
- Vehicle specifications
- For owners
Toyota CH-R Service Manual
- Introduction
- Maintenance
- Audio / Video
- Cellular Communication
- Navigation / Multi Info Display
- Park Assist / Monitoring
- Brake (front)
- Brake (rear)
- Brake Control / Dynamic Control Systems
- Brake System (other)
- Parking Brake
- Axle And Differential
- Drive Shaft / Propeller Shaft
- K114 Cvt
- 3zr-fae Battery / Charging
- Networking
- Power Distribution
- Power Assist Systems
- Steering Column
- Steering Gear / Linkage
- Alignment / Handling Diagnosis
- Front Suspension
- Rear Suspension
- Tire / Wheel
- Tire Pressure Monitoring
- Door / Hatch
- Exterior Panels / Trim
- Horn
- Lighting (ext)
- Mirror (ext)
- Window / Glass
- Wiper / Washer
- Door Lock
- Heating / Air Conditioning
- Interior Panels / Trim
- Lighting (int)
- Meter / Gauge / Display
- Mirror (int)
- Power Outlets (int)
- Pre-collision
- Seat
- Seat Belt
- Supplemental Restraint Systems
- Theft Deterrent / Keyless Entry
0.0124