DISASSEMBLY
PROCEDURE
1. REMOVE REAR BUMPER UPPER COVER LH
(a) Disengage the hook to remove the rear bumper upper cover LH. |
|
2. REMOVE REAR BUMPER UPPER COVER RH
HINT:
Use the same procedure as for the LH side.
3. REMOVE FOG LIGHT BRACKET
(a) Remove the 2 screws. |
|
(b) Disengage the guides to remove the fog light bracket.
4. REMOVE REFLEX REFLECTOR ASSEMBLY LH
(a) Remove the screw. |
|
(b) Disengage the claw and guide to remove the reflex reflector assembly LH.
5. REMOVE REFLEX REFLECTOR ASSEMBLY RH
HINT:
Use the same procedure as for the LH side.
6. REMOVE REAR BUMPER PLATE LH
(a) Remove the 2 screws. |
|
(b) Disengage the claws to remove the rear bumper plate LH.
7. REMOVE REAR BUMPER PLATE RH
HINT:
Use the same procedure as for the LH side.
8. REMOVE NO. 1 REAR BUMPER PLATE
(a) Disengage the claws. |
|
(b) Disengage the hook to remove the No. 1 rear bumper plate.
9. REMOVE REAR BUMPER PAD
(a) for USA and Canada:
(1) Remove the rear bumper pad. |
|
(b) except USA and Canada:
(1) Remove the rear bumper pad. |
|
10. REMOVE REAR BUMPER PAD LH
(a) Remove the rear bumper pad LH. |
|
11. REMOVE REAR BUMPER PAD RH
HINT:
Use the same procedure as for the LH side.
12. REMOVE REAR BUMPER SIDE STAY LH
(a) Remove the screw. |
|
(b) Remove the clip.
(c) Disengage the claw to remove the rear bumper side stay LH.
13. REMOVE REAR BUMPER SIDE STAY RH
HINT:
Use the same procedure as for the LH side.
14. REMOVE REAR BUMPER CENTER GUARD
(a) Remove the 2 clips. |
|
(b) Remove the 6 outside moulding retainers.
(c) Disengage the claws and guides to remove the rear bumper center guard. |
|
15. REMOVE REAR BUMPER SIDE RETAINER LH
(a) Remove the 2 screws. |
|
(b) Disengage the claw and guide to remove the rear bumper side retainer LH as shown in the illustration.
![]() |
Remove in this Direction (1) |
![]() |
Remove in this Direction (2) |
16. REMOVE REAR BUMPER SIDE RETAINER RH
HINT:
Use the same procedure as for the LH side.
17. REMOVE REAR COMBINATION LIGHT COVER LH
Click here
Click here
18. REMOVE REAR COMBINATION LIGHT COVER RH
HINT:
Use the same procedure as for the LH side.
19. REMOVE REAR COMBINATION LIGHT LH
Click here
Click here
20. REMOVE REAR COMBINATION LIGHT RH
HINT:
Use the same procedure as for the LH side.
21. REMOVE REAR BUMPER UPPER RETAINER LH
(a) Disengage the guides to remove the rear bumper upper retainer LH. |
|
22. REMOVE REAR BUMPER UPPER RETAINER RH
HINT:
Use the same procedure as for the LH side.
23. REMOVE REAR BUMPER REINFORCEMENT SUB-ASSEMBLY
(a) for USA and Canada:
(1) Remove the 6 bolts. |
|
(2) Disengage the guides to remove the rear bumper reinforcement sub-assembly.
(b) except USA and Canada:
(1) Remove the 8 bolts and rear bumper reinforcement sub-assembly. |
|
24. REMOVE REAR BUMPER ARM SUB-ASSEMBLY LH (for USA and Canada)
(a) Remove the 4 bolts and rear bumper arm sub-assembly LH. |
|
25. REMOVE REAR BUMPER ARM SUB-ASSEMBLY RH (for USA and Canada)
HINT:
Use the same procedure as for the LH side.
Toyota CH-R Service Manual > Generator: Reassembly
REASSEMBLY
PROCEDURE
1. INSTALL GENERATOR DRIVE END FRAME BEARING
(a) Using SST and a press, install a new generator drive end frame bearing.
SST: 09950-60010
09951-00470
SST: 09950-70010
09951-07100
(b) Fit the ta ...
Toyota CH-R Service Manual > Srs Seat Cushion Airbag Assembly: Removal
REMOVAL
CAUTION / NOTICE / HINT
The necessary procedures (adjustment, calibration, initialization, or registration)
that must be performed after parts are removed, installed, or replaced during the
front seat cushion airbag assembly RH removal/installation are shown below.
Necessary Procedure ...