COMPONENTS
ILLUSTRATION
*A |
w/ Illumination |
*B |
for Driver Side |
*C |
for Front Passenger Side |
- |
- |
*1 |
FRONT DOOR BELT SEAL |
*2 |
FRONT DOOR GLASS INNER WEATHERSTRIP |
*3 |
FRONT DOOR INSIDE HANDLE BEZEL PLUG |
*4 |
FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY |
*5 |
FRONT DOOR LOWER FRAME BRACKET GARNISH |
*6 |
FRONT DOOR TRIM BOARD SUB-ASSEMBLY |
*7 |
FRONT DOOR VENT SEAL |
*8 |
MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY WITH FRONT ARMREST BASE UPPER PANEL |
*9 |
NO. 1 INTERIOR ILLUMINATION LIGHT ASSEMBLY |
*10 |
POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT ARMREST BASE UPPER PANEL |
ILLUSTRATION
*A |
w/ Airbag Sensor |
*B |
for TMMT Made |
*C |
for TMC Made |
- |
- |
*1 |
DOOR FRAME UPPER GARNISH |
*2 |
DOOR SIDE AIRBAG SENSOR |
*3 |
FRONT DOOR BELT MOULDING ASSEMBLY |
*4 |
FRONT DOOR GLASS RUN |
*5 |
FRONT DOOR GLASS SUB-ASSEMBLY |
*6 |
FRONT DOOR SERVICE HOLE COVER |
*7 |
FRONT DOOR WINDOW REGULATOR ASSEMBLY |
*8 |
NO. 2 FRONT DOOR SERVICE HOLE COVER |
*9 |
OUTER MIRROR PROTECTOR |
*10 |
OUTER REAR VIEW MIRROR ASSEMBLY |
*11 |
HOLE PLUG |
- |
- |
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) |
N*m (kgf*cm, ft.*lbf): Specified torque |
||
● |
Non-reusable part |
MP grease |
ILLUSTRATION
*A |
for Driver Side |
*B |
for Front Passenger Side |
*1 |
FRONT DOOR FIX WINDOW GLASS |
*2 |
FRONT DOOR FIX WINDOW WEATHERSTRIP |
*3 |
FRONT DOOR FRONT LOWER FRAME SUB-ASSEMBLY |
*4 |
FRONT DOOR FRONT OUTSIDE HANDLE PAD |
*5 |
FRONT DOOR LOCK OPEN ROD |
*6 |
FRONT DOOR LOCK WITH MOTOR ASSEMBLY |
*7 |
FRONT DOOR OUTSIDE HANDLE ASSEMBLY |
*8 |
FRONT DOOR OUTSIDE HANDLE COVER |
*9 |
FRONT DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY |
*10 |
FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY |
*11 |
FRONT DOOR REAR OUTSIDE HANDLE PAD |
*12 |
DOOR LOCK WIRING HARNESS SEAL |
*13 |
FRONT DOOR LOCK CYLINDER ASSEMBLY |
*14 |
HOLE PLUG |
N*m (kgf*cm, ft.*lbf): Specified torque |
● |
Non-reusable part |
|
MP grease |
- |
- |
ILLUSTRATION
*1 |
FRONT DOOR CHECK ASSEMBLY |
*2 |
FRONT DOOR DUST PROOF SEAL |
*3 |
FRONT DOOR OUTSIDE MOULDING |
*4 |
FRONT DOOR OUTSIDE MOULDING SUB-ASSEMBLY |
*5 |
FRONT DOOR PANEL CUSHION |
*6 |
FRONT DOOR WEATHERSTRIP |
*7 |
FRONT NO. 1 SPEAKER ASSEMBLY |
*8 |
HOLE CAP |
*9 |
RIVET |
*10 |
HOLE COVER |
*11 |
GASKET |
- |
- |
N*m (kgf*cm, ft.*lbf): Specified torque |
● |
Non-reusable part |
|
MP grease |
Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent |
||
★ |
Precoated part |
- |
- |
ILLUSTRATION
*A |
for TMMT Made |
*B |
for TMC Made |
*1 |
FRONT DOOR FRONT WINDOW FRAME MOULDING |
*2 |
FRONT DOOR OUTSIDE STRIPE |
*3 |
FRONT DOOR UPPER WINDOW FRAME MOULDING |
*4 |
NO. 2 FRONT DOOR STRIPE |
*5 |
NO. 4 FRONT DOOR STRIPE |
*6 |
FRONT DOOR PANEL SUB-ASSEMBLY |
*7 |
RIVET |
- |
- |
N*m (kgf*cm, ft.*lbf): Specified torque |
● |
Non-reusable part |
|
Anti-rust coating |
- |
- |
ILLUSTRATION
*1 |
COWL SIDE TRIM BOARD |
*2 |
FRONT DOOR SCUFF PLATE |
Toyota CH-R Service Manual > Front Seat Outer Belt Assembly: Disposal
DISPOSAL
CAUTION / NOTICE / HINT
CAUTION:
Before performing pre-disposal deployment of any SRS part, review and closely
follow all applicable environmental and hazardous material regulations. Pre-disposal
deployment may be considered hazardous material treatment.
PROCEDURE
1. PRECAUTION
...
Toyota CH-R Service Manual > Rear Bumper: Disassembly
DISASSEMBLY
PROCEDURE
1. REMOVE REAR BUMPER UPPER COVER LH
(a) Disengage the hook to remove the rear bumper upper cover LH.
2. REMOVE REAR BUMPER UPPER COVER RH
HINT:
Use the same procedure as for the LH side.
3. REMOVE FOG LIGHT BRAC ...