Toyota CH-R Service Manual: Steering Pad Switch Circuit

Toyota CH-R Service Manual / Audio / Video / Audio And Visual System(for Radio And Display Type) / Steering Pad Switch Circuit

DESCRIPTION

This circuit sends an operation signal from the steering pad switch assembly to the radio and display receiver assembly.

If there is an open in the circuit, the audio system cannot be operated using the steering pad switch assembly.

If there is a short in the circuit, the same condition as when a switch is continuously depressed occurs. Therefore, the radio and display receiver assembly cannot be operated using the steering pad switch assembly, also the radio and display receiver assembly itself will not function.

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

The vehicle is equipped with a Supplemental Restraint System (SRS) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precaution for Supplemental Restraint System.

Click here

PROCEDURE

1.	CHECK HARNESS AND CONNECTOR (STEERING PAD SWITCH SIGNAL)

(a) Disconnect the F129 radio and display receiver assembly connector.

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection	Condition	Specified Condition
F129-21 (SW1) - F129-24 (SWG)	No switch pushed	95 to 105 kΩ
	Seek+ switch pushed	Below 2.5 Ω
	Seek- switch pushed	313 to 345 Ω
	Volume+ switch pushed	950 to 1050 Ω
	Volume- switch pushed	2955 to 3265 Ω
F129-22 (SW2) - F129-24 (SWG)	No switch pushed	95 to 105 kΩ
	MODE switch pushed	Below 2.5 Ω
	On hook switch pushed	313 to 345 Ω
	Off hook switch pushed	950 to 1050 Ω
	Voice switch pushed	2955 to 3265 Ω

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

2.	INSPECT STEERING PAD SWITCH ASSEMBLY

(a) Remove the steering pad switch assembly.

Click here

(b) Inspect the steering pad switch assembly.

Click here

REPLACE STEERING PAD SWITCH ASSEMBLY

3.	INSPECT SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY

(a) Remove the spiral cable with sensor sub-assembly.

Click here

(b) Inspect the spiral cable with sensor sub-assembly.

Click here

NOTICE:

Press and hold the lock located in the center of the spiral cable with sensor sub-assembly to rotate the spiral cable with sensor sub-assembly.
The spiral cable with sensor sub-assembly is an important part of the SRS airbag system. Incorrect removal or installation of the spiral cable with sensor sub-assembly may prevent the airbag from deploying.
As the spiral cable with sensor sub-assembly may break, do not rotate the spiral cable with sensor sub-assembly more than the specified amount.

REPAIR OR REPLACE HARNESS OR CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY OR BODY GROUND)

REPLACE SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY

Vehicle Speed Signal Circuit between Radio Receiver and Combination Meter

DESCRIPTION for Automatic Sound Levelizer (ASL): This circuit is necessary for the Automatic Sound Levelizer (ASL) built into the radio and display receiver assembly. The Automatic So ...

Illumination Circuit

DESCRIPTION Power is supplied to the radio and display receiver assembly and steering pad switch assembly illumination when the light control switch is in the tail or head position. WIRING DIAGR ...

Other materials:

Toyota CH-R Owners Manual > Do-it-yourself maintenance: Tires
Replace or rotate tires in accordance with maintenance schedules and treadwear. Checking tires Check if the treadwear indicators are showing on the tires. Also check the tires for uneven wear, such as excessive wear on one side of the tread. Check the spare tire condition and pressure if not ...

Toyota CH-R Service Manual > Back Door Lock: Removal
REMOVAL PROCEDURE 1. REMOVE PACKAGE TRAY TRIM PANEL ASSEMBLY (w/ Package Tray Trim) Click here 2. REMOVE TONNEAU COVER ASSEMBLY (w/ Tonneau Cover) Click here 3. REMOVE BACK DOOR TRIM UPPER PANEL ASSEMBLY Click here 4. REMOVE BACK DOOR SIDE GARNISH LH Click here 5. R ...