Toyota CH-R Service Manual: On-vehicle Inspection
ON-VEHICLE INSPECTION
CAUTION / NOTICE / HINT
CAUTION:
Be sure to correctly follow the removal and installation procedures for the door side airbag sensors.
PROCEDURE
1. INSPECT DOOR SIDE AIRBAG SENSOR (for Vehicle not Involved in Collision)
(a) Perform a diagnostic system check.
Click here .gif)
2. INSPECT DOOR SIDE AIRBAG SENSOR (for Vehicle Involved in Collision and Airbag not Deployed)
(a) Perform a diagnostic system check.
Click here
(b) Visually check the door side airbag sensors for defects if a front door of the vehicle or the area around a front door is damaged.
HINT:
The defects are as follows:
- Cracks in the sensor housing
- Dents in the sensor housing
- Chips in the sensor housing
- Cracks or other damage to the connector
- Damage to the waterproof rubber seal
- Peeling off of the label or damage to the serial number.
OK:
No defects are found.
If any defects are found, replace the door side airbag sensor with a new one.
3. INSPECT DOOR SIDE AIRBAG SENSOR (for Vehicle Involved in Collision and Airbag is Deployed)
(a) When airbags have deployed as the result of a collision, be sure to replace all door side airbag sensors in the damaged areas (anywhere in need of repair).
(b) Visually check the door side airbag sensors in undamaged areas for defects.
HINT:
The defects are as follows:
- Cracks in the sensor housing
- Dents in the sensor housing
- Chips in the sensor housing
- Cracks or other damage to the connector
- Damage to the waterproof rubber seal
- Peeling off of the label or damage to the serial number.
OK:
No defects are found.
If any defects are found or a door side airbag sensor has detected a major collision, replace the door side airbag sensor with a new one.
Components
COMPONENTS
ILLUSTRATION
*A
for Driver Side
*B
for Front Passenger Side
*1
DOOR SIDE AIRBAG SENSOR
*2
F ...
Removal
REMOVAL
CAUTION / NOTICE / HINT
The necessary procedures (adjustment, calibration, initialization, or registration)
that must be performed after parts are removed, installed, or replaced during th ...
Other materials:
Toyota CH-R Service Manual > Immobiliser System(w/ Smart Key System): Theft Deterrent System Communication Line High Fixation (B279A)
DESCRIPTION
If the communication line (IMI - EFIO) between the ECM and ID code box (immobiliser
code ECU) is stuck high, the ECM will store this DTC.
DTC No.
Detection Item
DTC Detection Condition
Trouble Area
Note
B279A
...
Toyota CH-R Service Manual > Blind Spot Monitor System: Master Module Horizontal Axis Misalignment (C1AC1)
DESCRIPTION
This DTC is stored when the angle of the blind spot monitor sensor LH (Master)
deviates more than the allowable range from the horizontal axis.
HINT:
If a drum tester such as a speedometer tester, brake/speedometer combination
tester or chassis dynamometer is used with t ...
Toyota CH-R Owners Manual
- For safety and security
- Instrument cluster
- Operation of each component
- Driving
- Interior features
- Maintenance and care
- When trouble arises
- Vehicle specifications
- For owners
Toyota CH-R Service Manual
- Introduction
- Maintenance
- Audio / Video
- Cellular Communication
- Navigation / Multi Info Display
- Park Assist / Monitoring
- Brake (front)
- Brake (rear)
- Brake Control / Dynamic Control Systems
- Brake System (other)
- Parking Brake
- Axle And Differential
- Drive Shaft / Propeller Shaft
- K114 Cvt
- 3zr-fae Battery / Charging
- Networking
- Power Distribution
- Power Assist Systems
- Steering Column
- Steering Gear / Linkage
- Alignment / Handling Diagnosis
- Front Suspension
- Rear Suspension
- Tire / Wheel
- Tire Pressure Monitoring
- Door / Hatch
- Exterior Panels / Trim
- Horn
- Lighting (ext)
- Mirror (ext)
- Window / Glass
- Wiper / Washer
- Door Lock
- Heating / Air Conditioning
- Interior Panels / Trim
- Lighting (int)
- Meter / Gauge / Display
- Mirror (int)
- Power Outlets (int)
- Pre-collision
- Seat
- Seat Belt
- Supplemental Restraint Systems
- Theft Deterrent / Keyless Entry
0.01