Toyota CH-R Service Manual: How To Proceed With Troubleshooting
CAUTION / NOTICE / HINT
HINT:
- Use the following procedure to troubleshoot the airbag system.
- *: Use the Techstream.
PROCEDURE
|
1. |
VEHICLE BROUGHT TO WORKSHOP |
|
.gif)
|
2. |
CUSTOMER PROBLEM ANALYSIS |
(a) Confirm problem symptoms.
Click here .gif)
|
|
3. |
CHECK CAN COMMUNICATION SYSTEM* |
(a) Using the Techstream, check if the CAN communication system is functioning normally.
OK:
CAN communication system is functioning normally.
HINT:
- Refer to CAN Bus Check in CAN Communication System.
Click here
- The airbag sensor assembly is connected to the CAN communication system. Therefore, before starting troubleshooting, make sure to check that there are no malfunctions in the CAN communication system.
| NG | .gif) |
GO TO CAN COMMUNICATION SYSTEM |
|
|
4. |
SRS WARNING LIGHT CHECK |
(a) Proceed to Diagnosis System.
Click here
|
|
5. |
CHECK FOR DTC* |
(a) Proceed to DTC Check / Clear.
Click here
OK:
DTCs are not output.
| NG | |
GO TO STEP 12 |
|
|
6. |
SYMPTOM SIMULATION |
(a) Proceed to How to Proceed with Troubleshooting.
Click here
|
|
7. |
PROBLEM SYMPTOMS TABLE |
(a) Proceed to Problem Symptoms Table.
Click here
|
|
8. |
CIRCUIT INSPECTION* |
|
|
9. |
IDENTIFICATION OF PROBLEM |
|
|
10. |
REPAIR OR REPLACEMENT |
|
|
11. |
CONFIRMATION TEST |
| NEXT | |
END |
|
12. |
DIAGNOSTIC TROUBLE CODE CHART |
(a) Proceed to Diagnostic Trouble Code Chart.
Click here
|
|
13. |
CIRCUIT INSPECTION* |
|
|
14. |
IDENTIFICATION OF PROBLEM |
|
|
15. |
REPAIR OR REPLACEMENT |
|
|
16. |
CONFIRMATION TEST |
| NEXT | |
END |
System Description
SYSTEM DESCRIPTION
GENERAL
(a) Acceleration sensors and pressure sensors used for the airbag system are
installed to various parts on the vehicle and calculate the acceleration rate and
pressure ...
Problem Symptoms Table
PROBLEM SYMPTOMS TABLE
HINT:
Use the table below to help determine the cause of problem symptoms.
If multiple suspected areas are listed, the potential causes of the symptoms
are lis ...
Other materials:
Toyota CH-R Service Manual > Washer Level Warning Switch: Installation
INSTALLATION
PROCEDURE
1. INSTALL LEVEL WARNING SWITCH ASSEMBLY
(a) Install the level warning switch assembly as shown in the illustration.
Install in this Direction
(b) Connect the connector.
2. ADD WASHER FLUID
Click here
3. INSTALL FRONT FENDER LINER RH
...
Toyota CH-R Service Manual > Automatic Headlight Beam Level Control System: Data List / Active Test
DATA LIST / ACTIVE TEST
DATA LIST
NOTICE:
In the table below, the values listed under "Normal Condition" are reference
values. Do not depend solely on these reference values when deciding whether a part
is faulty or not.
HINT:
Using the Techstream to read the Data List allows the ...
Toyota CH-R Owners Manual
- For safety and security
- Instrument cluster
- Operation of each component
- Driving
- Interior features
- Maintenance and care
- When trouble arises
- Vehicle specifications
- For owners
Toyota CH-R Service Manual
- Introduction
- Maintenance
- Audio / Video
- Cellular Communication
- Navigation / Multi Info Display
- Park Assist / Monitoring
- Brake (front)
- Brake (rear)
- Brake Control / Dynamic Control Systems
- Brake System (other)
- Parking Brake
- Axle And Differential
- Drive Shaft / Propeller Shaft
- K114 Cvt
- 3zr-fae Battery / Charging
- Networking
- Power Distribution
- Power Assist Systems
- Steering Column
- Steering Gear / Linkage
- Alignment / Handling Diagnosis
- Front Suspension
- Rear Suspension
- Tire / Wheel
- Tire Pressure Monitoring
- Door / Hatch
- Exterior Panels / Trim
- Horn
- Lighting (ext)
- Mirror (ext)
- Window / Glass
- Wiper / Washer
- Door Lock
- Heating / Air Conditioning
- Interior Panels / Trim
- Lighting (int)
- Meter / Gauge / Display
- Mirror (int)
- Power Outlets (int)
- Pre-collision
- Seat
- Seat Belt
- Supplemental Restraint Systems
- Theft Deterrent / Keyless Entry
0.0095